Phoenix Contact · Connection Cable
2926218 is a Phoenix Contact connection cable with Rated current Ie up to 4 A; Enclosure rating IP67 (IEC 60529); Operating temperature -25...+80 °C (IEC 60068-2-1). It is used in control panels, machine builds, spare-part replacements where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Rated current Ieup to 4 A
-
Enclosure ratingIP67 (IEC 60529)
-
Operating temperature-25...+80 °C (IEC 60068-2-1)
-
CertificationsCE, UL, cULus
Specifications
| Electrical |
| Rated current Ie |
up to 4 A |
| Tripping characteristic |
150 mm |
| Rated torque |
0.2 Nm |
| I/O and communication |
| Flame detection |
IEC 60332-1-2 (raw cable) |
| Mechanical |
| Weight |
976.6 g |
| Terminal wire size |
Assembled shielded round cable |
| Enclosure rating |
IP67 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
-25...+80 °C (IEC 60068-2-1) |
| Certifications |
CE, UL, cULus |
| Degree of protection |
≥ IP54 (Installation location) |
Values follow the Phoenix Contact Connection Cable specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Connection Cable variants |
| Catalog number |
Rated current Ie |
|
2926218 (this page) |
up to 4 A |
| 2926234 |
up to 4 A |
| 2926250 |
up to 4 A |
| 2926263 |
up to 4 A |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The 2926218 is the device-level element in a Phoenix Contact connection cable installation. It receives the field signals and control supply listed above — the rated supply — and switches or conditions the load within the up to 4 A ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in control panels, machine builds, spare-part replacements, where the unit is matched to the original catalog number and the enclosure provides standard panel or DIN-rail support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 2926218
Phoenix Contact 2926218 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 2926218; confirm the installed unit's part number and revision so the replacement matches both electrically and mechanically.
- Flame detection: IEC 60332-1-2 (raw cable) — Check this value against the nameplate of the installed unit before ordering.
- Operating temperature: -25...+80 °C (IEC 60068-2-1) — Match it to the existing panel and upstream protection.
- Rated current Ie: up to 4 A — Record it with the other nameplate data when sourcing a replacement.
- Enclosure rating: IP67 (IEC 60529) — Confirm the revision of the installed unit before a like-for-like replacement.
Available from stock with datasheet, certificates and a quotation on request.
Common questions about 2926218
Q.Before ordering 2926218, which rated torque entry should be checked?
The rated torque entry quoted above is 0.2 Nm. Check the revision of the installed unit if the catalog number has been superseded.
Q.Where can I find the certifications data for 2926218?
It is listed in the specification table for Phoenix Contact 2926218 as CE, UL, cULus. Compare it with the nameplate of the installed unit before ordering.
Q.For 2926218, what does the specification table state about tripping characteristic?
The specification table lists tripping characteristic = 150 mm for Phoenix Contact 2926218. Confirm this figure against the unit currently in the panel.
Q.What should I include in an enquiry for 2926218?
Send the full catalog number 2926218, the required quantity and a photo of the nameplate. Stock, lead time and the applicable compliance documents can then be confirmed for Phoenix Contact 2926218.
Q.How do I confirm compatibility of 2926218 before ordering?
Match the catalog number 2926218 and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.