Phoenix Contact · Connection Cable
2926250 is a Phoenix Contact connection cable with Rated current Ie up to 4 A; Enclosure rating IP67 (IEC 60529); Operating temperature -25...+80 °C (IEC 60068-2-1). It is used in control panels, machine builds, spare-part replacements where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Rated current Ieup to 4 A
-
Enclosure ratingIP67 (IEC 60529)
-
Operating temperature-25...+80 °C (IEC 60068-2-1)
-
CertificationsCE, UL, cULus
Specifications
| Electrical |
| Rated current Ie |
up to 4 A |
| Tripping characteristic |
ï‚» 150 mm |
| Rated torque |
0.2 Nm |
| I/O and communication |
| Flame detection |
IEC 60332-1-2 (raw cable) |
| Mechanical |
| Weight |
459 g |
| Terminal wire size |
Assembled shielded round cable |
| Enclosure rating |
IP67 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
-25...+80 °C (IEC 60068-2-1) |
| Certifications |
CE, UL, cULus |
| Degree of protection |
≥ IP54 (Installation location) |
Values follow the Phoenix Contact Connection Cable specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Connection Cable variants |
| Catalog number |
Rated current Ie |
|
2926250 (this page) |
up to 4 A |
| 2926218 |
up to 4 A |
| 2926234 |
up to 4 A |
| 2926263 |
up to 4 A |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The 2926250 is the device-level element in a Phoenix Contact connection cable installation. It receives the field signals and control supply listed above — the rated supply — and switches or conditions the load within the up to 4 A ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in control panels, machine builds, spare-part replacements, where the unit is matched to the original catalog number and the enclosure provides standard panel or DIN-rail support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 2926250
Phoenix Contact 2926250 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 2926250; record the nameplate data of the unit being replaced before selecting an equivalent.
- Rated current Ie: up to 4 A — Confirm the revision of the installed unit before a like-for-like replacement.
- Tripping characteristic:  150 mm — Use it as the reference when cross-checking a current-production equivalent.
- Terminal wire size: Assembled shielded round cable — Verify it in the project documentation before confirming the order.
- Flame detection: IEC 60332-1-2 (raw cable) — Check this value against the nameplate of the installed unit before ordering.
For a discontinued unit, match function and electrical ratings rather than the label alone.
Common questions about 2926250
Q.For 2926250, what does the specification table state about rated current Ie?
The specification table lists rated current Ie = up to 4 A for Phoenix Contact 2926250. Check the revision of the installed unit if the catalog number has been superseded.
Q.Which value is published under weight for catalog number 2926250?
For 2926250, weight is given as 459 g. Compare it with the nameplate of the installed unit before ordering.
Q.Before ordering 2926250, which terminal wire size entry should be checked?
The terminal wire size entry quoted above is Assembled shielded round cable. Confirm this figure against the unit currently in the panel.
Q.What should I include in an enquiry for 2926250?
Send the full catalog number 2926250, the required quantity and a photo of the nameplate. Stock, lead time and the applicable compliance documents can then be confirmed for Phoenix Contact 2926250.
Q.How do I confirm compatibility of 2926250 before ordering?
Match the catalog number 2926250 and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.