Phoenix Contact · Connection Cable
1407473 is a Phoenix Contact circuit breaker with Rated current Ie up to 4 A; Breaking capacity Icu/Ics CAT6A; Enclosure rating IP67 (IEC 60529). It is used in distribution boards, motor protection circuits, panel feeders where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Rated current Ieup to 4 A
-
Breaking capacity Icu/IcsCAT6A
-
Enclosure ratingIP67 (IEC 60529)
-
Operating temperature-25...+80 °C (IEC 60068-2-1)
Specifications
| Electrical |
| Rated current Ie |
up to 4 A |
| Breaking capacity Icu/Ics |
CAT6A |
| Rated torque |
0.4 Nm (M12 connector) |
| Rated speed |
10 Gbps |
| I/O and communication |
| Bus interface |
Ethernet |
| Flame detection |
according to IEC 60332-1-2 |
| Mechanical |
| Dimensions (H x W x D) |
Pin assignment of M12 plug, 8-pos., X-coded, pin side view |
| Weight |
261 g |
| Terminal wire size |
4x2xAWG26/7; S/FTP |
| Enclosure rating |
IP67 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
-25...+80 °C (IEC 60068-2-1) |
| Certifications |
CE, UL, cULus |
Values follow the Phoenix Contact Connection Cable specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Connection Cable variants |
| Catalog number |
Breaking capacity Icu/Ics |
|
1407473 (this page) |
CAT6A |
| 1407474 |
CAT6A |
| 1407487 |
— |
| 1407363 |
— |
Verify model-specific dimensions, terminals and installation requirements in the manufacturer documentation before selecting an alternative.
Where it sits in the control system
The 1407473 is the device-level element in a Phoenix Contact circuit breaker installation. It receives the field signals and control supply listed above — the rated supply — and switches or conditions the load within the up to 4 A ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in distribution boards, motor protection circuits, panel feeders, where the unit is matched to the original catalog number and the enclosure provides standard panel or DIN-rail support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 1407473
Phoenix Contact 1407473 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 1407473; confirm the installed unit's part number and revision so the replacement matches both electrically and mechanically.
- Rated speed: 10 Gbps — Confirm the revision of the installed unit before a like-for-like replacement.
- Certifications: CE, UL, cULus — Use it as the reference when cross-checking a current-production equivalent.
- Operating temperature: -25...+80 °C (IEC 60068-2-1) — Verify it in the project documentation before confirming the order.
- Terminal wire size: 4x2xAWG26/7; S/FTP — Check this value against the nameplate of the installed unit before ordering.
For a discontinued unit, match function and electrical ratings rather than the label alone.
Common questions about 1407473
Q.Where can I find the dimensions (H x W x D) data for 1407473?
It is listed in the specification table for Phoenix Contact 1407473 as Pin assignment of M12 plug, 8-pos., X-coded, pin side view. Use the value as the reference when sourcing a current-production equivalent.
Q.For 1407473, what does the specification table state about weight?
The specification table lists weight = 261 g for Phoenix Contact 1407473. Check the revision of the installed unit if the catalog number has been superseded.
Q.Which value is published under breaking capacity Icu/Ics for catalog number 1407473?
For 1407473, breaking capacity Icu/Ics is given as CAT6A. Compare it with the nameplate of the installed unit before ordering.
Q.What should I include in an enquiry for 1407473?
Send the full catalog number 1407473, the required quantity and a photo of the nameplate. Stock, lead time and the applicable compliance documents can then be confirmed for Phoenix Contact 1407473.
Q.How do I confirm compatibility of 1407473 before ordering?
Match the catalog number 1407473 and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.