Phoenix Contact · Connection Cable
1407474 is a Phoenix Contact circuit breaker with Rated current Ie up to 4 A; Breaking capacity Icu/Ics CAT6A; Enclosure rating IP67 (IEC 60529). It is used in distribution boards, motor protection circuits, panel feeders where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Rated current Ieup to 4 A
-
Breaking capacity Icu/IcsCAT6A
-
Enclosure ratingIP67 (IEC 60529)
-
Operating temperature-25...+80 °C (IEC 60068-2-1)
Specifications
| Electrical |
| Rated current Ie |
up to 4 A |
| Breaking capacity Icu/Ics |
CAT6A |
| Rated torque |
0.4 Nm (M12 connector) |
| Rated speed |
10 Gbps |
| I/O and communication |
| Bus interface |
Ethernet |
| Flame detection |
according to IEC 60332-1-2 |
| Mechanical |
| Dimensions (H x W x D) |
Pin assignment of M12 plug, 8-pos., X-coded, pin side view |
| Weight |
499 g |
| Terminal wire size |
4x2xAWG26/7; S/FTP |
| Enclosure rating |
IP67 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
-25...+80 °C (IEC 60068-2-1) |
| Certifications |
CE, UL, cULus |
Values follow the Phoenix Contact Connection Cable specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Connection Cable variants |
| Catalog number |
Breaking capacity Icu/Ics |
|
1407474 (this page) |
CAT6A |
| 1407473 |
CAT6A |
| 1407487 |
— |
| 1407363 |
— |
Verify model-specific dimensions, terminals and installation requirements in the manufacturer documentation before selecting an alternative.
Where it sits in the control system
The 1407474 is the device-level element in a Phoenix Contact circuit breaker installation. It receives the field signals and control supply listed above — the rated supply — and switches or conditions the load within the up to 4 A ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in distribution boards, motor protection circuits, panel feeders, where the unit is matched to the original catalog number and the enclosure provides standard panel or DIN-rail support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 1407474
Phoenix Contact 1407474 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 1407474; always cross-check the catalog number and hardware revision on the nameplate before placing an order.
- Certifications: CE, UL, cULus — Use it as the reference when cross-checking a current-production equivalent.
- Rated speed: 10 Gbps — Verify it in the project documentation before confirming the order.
- Rated torque: 0.4 Nm (M12 connector) — Check this value against the nameplate of the installed unit before ordering.
- Bus interface: Ethernet — Match it to the existing panel and upstream protection.
Cross-check the ratings above with the installed device before confirming the order.
Common questions about 1407474
Q.Where can I find the dimensions (H x W x D) data for 1407474?
It is listed in the specification table for Phoenix Contact 1407474 as Pin assignment of M12 plug, 8-pos., X-coded, pin side view. Compare it with the nameplate of the installed unit before ordering.
Q.For 1407474, what does the specification table state about weight?
The specification table lists weight = 499 g for Phoenix Contact 1407474. Confirm this figure against the unit currently in the panel.
Q.Which value is published under flame detection for catalog number 1407474?
For 1407474, flame detection is given as according to IEC 60332-1-2. Use the value as the reference when sourcing a current-production equivalent.
Q.Can the 1407474 replace the unit currently installed in my panel?
Compare catalog number 1407474 and the ratings above with the nameplate of the installed device. A current-production equivalent is selected by function and electrical rating, not by the label alone.
Q.How do I confirm compatibility of 1407474 before ordering?
Match the catalog number 1407474 and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.