Phoenix Contact · Connection Cable
1413146 is a Phoenix Contact circuit breaker with Rated current Ie up to 4 A; Breaking capacity Icu/Ics CAT5; Enclosure rating IP67 (IEC 60529). It is used in distribution boards, motor protection circuits, panel feeders where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Rated current Ieup to 4 A
-
Breaking capacity Icu/IcsCAT5
-
Enclosure ratingIP67 (IEC 60529)
-
Operating temperature-25...+80 °C (IEC 60068-2-1)
Specifications
| Electrical |
| Rated current Ie |
up to 4 A |
| Breaking capacity Icu/Ics |
CAT5 |
| Rated speed |
1 Gbps |
| I/O and communication |
| Flame detection |
according to IEC 60332-1-2 |
| Mechanical |
| Weight |
57 kg/km |
| Terminal wire size |
Bare Cu litz wires |
| Enclosure rating |
IP67 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
-25...+80 °C (IEC 60068-2-1) |
| Certifications |
CE, UL, cULus |
Values follow the Phoenix Contact Connection Cable specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Connection Cable variants |
| Catalog number |
Mounting |
|
1413146 (this page) |
— |
| 1411043 |
— |
| 1411044 |
— |
| 1411366 |
— |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The 1413146 is the device-level element in a Phoenix Contact circuit breaker installation. It receives the field signals and control supply listed above — the rated supply — and switches or conditions the load within the up to 4 A ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in distribution boards, motor protection circuits, panel feeders, where the unit is matched to the original catalog number and the enclosure provides standard panel or DIN-rail support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 1413146
Phoenix Contact 1413146 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 1413146; confirm the installed unit's part number and revision so the replacement matches both electrically and mechanically.
- Weight: 57 kg/km — Use it as the reference when cross-checking a current-production equivalent.
- Enclosure rating: IP67 (IEC 60529) — Verify it in the project documentation before confirming the order.
- Terminal wire size: Bare Cu litz wires — Check this value against the nameplate of the installed unit before ordering.
- Rated current Ie: up to 4 A — Match it to the existing panel and upstream protection.
For a discontinued unit, match function and electrical ratings rather than the label alone.
Common questions about 1413146
Q.Where can I find the rated current Ie data for 1413146?
It is listed in the specification table for Phoenix Contact 1413146 as up to 4 A. Check the revision of the installed unit if the catalog number has been superseded.
Q.For 1413146, what does the specification table state about rated speed?
The specification table lists rated speed = 1 Gbps for Phoenix Contact 1413146. Compare it with the nameplate of the installed unit before ordering.
Q.Which value is published under certifications for catalog number 1413146?
For 1413146, certifications is given as CE, UL, cULus. Confirm this figure against the unit currently in the panel.
Q.How do I confirm compatibility of 1413146 before ordering?
Match the catalog number 1413146 and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.
Q.Can the 1413146 replace the unit currently installed in my panel?
Compare catalog number 1413146 and the ratings above with the nameplate of the installed device. A current-production equivalent is selected by function and electrical rating, not by the label alone.