Phoenix Contact · Connector
1407505 is a Phoenix Contact circuit breaker with Breaking capacity Icu/Ics CAT5; Enclosure rating IP20 (IEC 60529); Mounting DIN rail / panel. It is used in distribution boards, motor protection circuits, panel feeders where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Breaking capacity Icu/IcsCAT5
-
Enclosure ratingIP20 (IEC 60529)
-
MountingDIN rail / panel
-
Operating temperature0...+55 °C (IEC 60068-2-1)
Specifications
| Electrical |
| Breaking capacity Icu/Ics |
CAT5 |
| Rated torque |
2 Nm ... 3 Nm (Installation-side) |
| Rated speed |
100 Mbps |
| I/O and communication |
| Flame detection |
in accordance with UL 2556, Section 9.1 and UL 1581, Section 1100 |
| Mechanical |
| Weight |
87 kg/km |
| Mounting |
DIN rail / panel |
| Terminal wire size |
1x4xAWG26 + 1x4xAWG20 |
| Enclosure rating |
IP20 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
0...+55 °C (IEC 60068-2-1) |
| Certifications |
CE, UL, cULus |
Values follow the Phoenix Contact Connector specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Connector variants |
| Catalog number |
Breaking capacity Icu/Ics |
Rated operational voltage |
|
1407505 (this page) |
CAT5 |
— |
| 1407504 |
CAT5 |
— |
| 1402398 |
CAT5 (IEC 11801:2002) |
<= 440 V AC |
| 1404549 |
CAT6A |
72 V (DC) |
Verify model-specific dimensions, terminals and installation requirements in the manufacturer documentation before selecting an alternative.
Where it sits in the control system
The 1407505 is the device-level element in a Phoenix Contact circuit breaker installation. It receives the field signals and control supply listed above — the rated supply — and switches or conditions the load within the the rated ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in distribution boards, motor protection circuits, panel feeders, where the unit is matched to the original catalog number and the enclosure provides DIN rail / panel support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 1407505
Phoenix Contact 1407505 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 1407505; verify the catalog number against your bill of materials before requesting a quotation.
- Flame detection: in accordance with UL 2556, Section 9.1 and UL 1581, Section 1100 — Match it to the existing panel and upstream protection.
- Rated torque: 2 Nm ... 3 Nm (Installation-side) — Record it with the other nameplate data when sourcing a replacement.
- Operating temperature: 0...+55 °C (IEC 60068-2-1) — Confirm the revision of the installed unit before a like-for-like replacement.
- Breaking capacity Icu/Ics: CAT5 — Use it as the reference when cross-checking a current-production equivalent.
Available from stock with datasheet, certificates and a quotation on request.
Common questions about 1407505
Q.For 1407505, what does the specification table state about rated torque?
The specification table lists rated torque = 2 Nm ... 3 Nm (Installation-side) for Phoenix Contact 1407505. Confirm this figure against the unit currently in the panel.
Q.Which value is published under mounting for catalog number 1407505?
For 1407505, mounting is given as DIN rail / panel. Use the value as the reference when sourcing a current-production equivalent.
Q.Before ordering 1407505, which rated speed entry should be checked?
The rated speed entry quoted above is 100 Mbps. Check the revision of the installed unit if the catalog number has been superseded.
Q.How do I confirm compatibility of 1407505 before ordering?
Match the catalog number 1407505 and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.
Q.What should I include in an enquiry for 1407505?
Send the full catalog number 1407505, the required quantity and a photo of the nameplate. Stock, lead time and the applicable compliance documents can then be confirmed for Phoenix Contact 1407505.