Phoenix Contact · Heavy-Duty Connector
1771480 is a Phoenix Contact circuit breaker with Rated current Ie 16 A; Tripping characteristic 7 mm; Rated operational voltage <= 440 V AC. It is used in distribution boards, motor protection circuits, panel feeders where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Rated current Ie16 A
-
Tripping characteristic7 mm
-
Rated operational voltage<= 440 V AC
-
Enclosure ratingIP20 (IEC 60529)
Specifications
| Electrical |
| Rated current Ie |
16 A |
| Rated operational voltage |
<= 440 V AC |
| Tripping characteristic |
7 mm |
| Rated torque |
0.5 Nm |
| Mechanical |
| Weight |
106.72 g |
| Mounting |
DIN rail / panel |
| Terminal wire size |
0.5 mm² ... 2.5 mm² (applies to stranded conductors with ferrules) |
| Enclosure rating |
IP20 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
-25...+60 °C |
| Certifications |
CE, UL, cULus |
Values follow the Phoenix Contact Heavy-Duty Connector specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Heavy-Duty Connector variants |
| Catalog number |
Tripping characteristic |
Rated operational voltage |
|
1771480 (this page) |
7 mm |
<= 440 V AC |
| 1771118 |
— |
— |
| 1771163 |
— |
— |
| 1771202 |
7 mm |
<= 440 V AC |
Verify model-specific dimensions, terminals and installation requirements in the manufacturer documentation before selecting an alternative.
Where it sits in the control system
The 1771480 is the device-level element in a Phoenix Contact circuit breaker installation. It receives the field signals and control supply listed above — <= 440 V AC — and switches or conditions the load within the 16 A ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in distribution boards, motor protection circuits, panel feeders, where the unit is matched to the original catalog number and the enclosure provides DIN rail / panel support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 1771480
Phoenix Contact 1771480 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 1771480; always cross-check the catalog number and hardware revision on the nameplate before placing an order.
- Tripping characteristic: 7 mm — Verify it in the project documentation before confirming the order.
- Weight: 106.72 g — Check this value against the nameplate of the installed unit before ordering.
- Certifications: CE, UL, cULus — Match it to the existing panel and upstream protection.
- Rated current Ie: 16 A — Record it with the other nameplate data when sourcing a replacement.
Datasheets and compliance documents are available on request; quote the full catalog number when enquiring.
Common questions about 1771480
Q.Where can I find the rated current Ie data for 1771480?
It is listed in the specification table for Phoenix Contact 1771480 as 16 A. Check the revision of the installed unit if the catalog number has been superseded.
Q.For 1771480, what does the specification table state about rated operational voltage?
The specification table lists rated operational voltage = <= 440 V AC for Phoenix Contact 1771480. Compare it with the nameplate of the installed unit before ordering.
Q.Which value is published under rated torque for catalog number 1771480?
For 1771480, rated torque is given as 0.5 Nm. Confirm this figure against the unit currently in the panel.
Q.Can the 1771480 replace the unit currently installed in my panel?
Compare catalog number 1771480 and the ratings above with the nameplate of the installed device. A current-production equivalent is selected by function and electrical rating, not by the label alone.
Q.What should I include in an enquiry for 1771480?
Send the full catalog number 1771480, the required quantity and a photo of the nameplate. Stock, lead time and the applicable compliance documents can then be confirmed for Phoenix Contact 1771480.