Phoenix Contact · circuit breaker
2908286 is a Phoenix Contact circuit breaker with Tripping characteristic 8 mm; Breaking capacity Icu/Ics up to 63rd harmonic; Supply voltage 100 V AC ... 400 V AC (±20 %). It is used in distribution boards, motor protection circuits, panel feeders where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Tripping characteristic8 mm
-
Breaking capacity Icu/Icsup to 63rd harmonic
-
Supply voltage100 V AC ... 400 V AC (±20 %)
-
Enclosure ratingIP20 (IEC 60529)
Specifications
| Electrical |
| Breaking capacity Icu/Ics |
up to 63rd harmonic |
| Tripping characteristic |
8 mm |
| Supply voltage |
100 V AC ... 400 V AC (±20 %) |
| Input voltage range |
18 V AC ... 690 V AC (Phase/Phase) |
| Power consumption |
≤ 4 W |
| Frequency |
50 Hz ... 60 Hz (AC sine) |
| Rated torque |
0.5 Nm ... 0.6 Nm |
| Rated speed |
10 Mbps |
| I/O and communication |
| Response time |
5 A |
| Mechanical |
| Weight |
397.34 g |
| Mounting |
DIN rail / panel |
| Terminal wire size |
0.2 mm² ... 6 mm² |
| Enclosure rating |
IP20 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
0...+55 °C (IEC 60068-2-1) |
| Certifications |
CE, UL, cULus |
| Humidity |
≤ 95 % (non-condensing) |
Values follow the Phoenix Contact circuit breaker specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact circuit breaker variants |
| Catalog number |
Breaking capacity Icu/Ics |
Tripping characteristic |
|
2908286 (this page) |
up to 63rd harmonic |
8 mm |
| 2966207 |
200 A (conditional short-circuit current) |
8 mm |
| 2982090 |
20 A |
8 mm |
| 2297293 |
Basic insulation |
8 mm |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The 2908286 is the device-level element in a Phoenix Contact circuit breaker installation. It receives the field signals and control supply listed above — 100 V AC ... 400 V AC (±20 %) — and switches or conditions the load within the the rated ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in distribution boards, motor protection circuits, panel feeders, where the unit is matched to the original catalog number and the enclosure provides DIN rail / panel support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 2908286
Phoenix Contact 2908286 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 2908286; confirm the installed unit's part number and revision so the replacement matches both electrically and mechanically.
- Frequency: 50 Hz ... 60 Hz (AC sine) — Check this value against the nameplate of the installed unit before ordering.
- Weight: 397.34 g — Match it to the existing panel and upstream protection.
- Enclosure rating: IP20 (IEC 60529) — Record it with the other nameplate data when sourcing a replacement.
- Supply voltage: 100 V AC ... 400 V AC (±20 %) — Confirm the revision of the installed unit before a like-for-like replacement.
For a discontinued unit, match function and electrical ratings rather than the label alone.
Common questions about 2908286
Q.Before ordering 2908286, which tripping characteristic entry should be checked?
The tripping characteristic entry quoted above is 8 mm. Compare it with the nameplate of the installed unit before ordering.
Q.Where can I find the frequency data for 2908286?
It is listed in the specification table for Phoenix Contact 2908286 as 50 Hz ... 60 Hz (AC sine). Confirm this figure against the unit currently in the panel.
Q.For 2908286, what does the specification table state about response time?
The specification table lists response time = 5 A for Phoenix Contact 2908286. Use the value as the reference when sourcing a current-production equivalent.
Q.How do I confirm compatibility of 2908286 before ordering?
Match the catalog number 2908286 and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.
Q.Can the 2908286 replace the unit currently installed in my panel?
Compare catalog number 2908286 and the ratings above with the nameplate of the installed device. A current-production equivalent is selected by function and electrical rating, not by the label alone.