Phoenix Contact · Surge Protection
2878117 is a Phoenix Contact circuit breaker with Tripping characteristic 8 mm; Breaking capacity Icu/Ics FO; Supply voltage 24 V DC (via voltage jumper). It is used in distribution boards, motor protection circuits, panel feeders where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Tripping characteristic8 mm
-
Breaking capacity Icu/IcsFO
-
Supply voltage24 V DC (via voltage jumper)
-
Enclosure ratingIP20 (IEC 60529)
Specifications
| Electrical |
| Breaking capacity Icu/Ics |
FO |
| Tripping characteristic |
8 mm |
| Supply voltage |
24 V DC (via voltage jumper) |
| Rated speed |
500 kbps |
| I/O and communication |
| Bus interface |
0 bit |
| Mechanical |
| Weight |
123.6 g |
| Mounting |
DIN rail / panel |
| Enclosure rating |
IP20 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
0...+55 °C (IEC 60068-2-1) |
| Certifications |
CE, UL, cULus |
| Humidity |
75 % (On average, 85 % occasionally) |
Values follow the Phoenix Contact Surge Protection specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Surge Protection variants |
| Catalog number |
Mounting |
|
2878117 (this page) |
DIN rail / panel |
| 2818643 |
DIN rail / panel |
| 2839208 |
DIN rail / panel |
| 2702258 |
DIN rail / panel |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The 2878117 is the device-level element in a Phoenix Contact circuit breaker installation. It receives the field signals and control supply listed above — 24 V DC (via voltage jumper) — and switches or conditions the load within the the rated ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in distribution boards, motor protection circuits, panel feeders, where the unit is matched to the original catalog number and the enclosure provides DIN rail / panel support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 2878117
Phoenix Contact 2878117 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 2878117; confirm the installed unit's part number and revision so the replacement matches both electrically and mechanically.
- Supply voltage: 24 V DC (via voltage jumper) — Confirm the revision of the installed unit before a like-for-like replacement.
- Humidity: 75 % (On average, 85 % occasionally) — Use it as the reference when cross-checking a current-production equivalent.
- Mounting: DIN rail / panel — Verify it in the project documentation before confirming the order.
- Weight: 123.6 g — Check this value against the nameplate of the installed unit before ordering.
Cross-check the ratings above with the installed device before confirming the order.
Common questions about 2878117
Q.Before ordering 2878117, which operating temperature entry should be checked?
The operating temperature entry quoted above is 0...+55 °C (IEC 60068-2-1). Compare it with the nameplate of the installed unit before ordering.
Q.Where can I find the breaking capacity Icu/Ics data for 2878117?
It is listed in the specification table for Phoenix Contact 2878117 as FO. Confirm this figure against the unit currently in the panel.
Q.For 2878117, what does the specification table state about enclosure rating?
The specification table lists enclosure rating = IP20 (IEC 60529) for Phoenix Contact 2878117. Use the value as the reference when sourcing a current-production equivalent.
Q.Can the 2878117 replace the unit currently installed in my panel?
Compare catalog number 2878117 and the ratings above with the nameplate of the installed device. A current-production equivalent is selected by function and electrical rating, not by the label alone.
Q.What should I include in an enquiry for 2878117?
Send the full catalog number 2878117, the required quantity and a photo of the nameplate. Stock, lead time and the applicable compliance documents can then be confirmed for Phoenix Contact 2878117.