Phoenix Contact · Soft Starter
1201695 is a Phoenix Contact variable-frequency drive with Overload capacity 150 % for 60 s (IEC 61800-2); Enclosure rating IP20 (IEC 60529); Frequency 50/60 Hz (IEC 61800-2). It is used in pump sets, conveyor belts, fan and compressor drives where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Overload capacity150 % for 60 s (IEC 61800-2)
-
Enclosure ratingIP20 (IEC 60529)
-
Frequency50/60 Hz (IEC 61800-2)
-
Rated current Ie2.8 A (no line reactor)
Specifications
| Electrical |
| Rated current Ie |
2.8 A (no line reactor) |
| Tripping characteristic |
10 mm |
| Supply voltage |
1-phase 200...240 V / 3-phase 380...480 V AC |
| Input voltage range |
380 V AC |
| Output current |
≤ 3.75 A (180 s) |
| Frequency |
50/60 Hz (IEC 61800-2) |
| Control method |
V/f, sensorless vector (IEC 61800-2) |
| Overload capacity |
150 % for 60 s (IEC 61800-2) |
| Mechanical |
| Weight |
1,366 g |
| Mounting |
DIN rail mounting |
| Terminal wire size |
0.2 mm² ... 6 mm² |
| Enclosure rating |
IP20 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
-10...+60 °C (IEC 60068-2-1) |
| Certifications |
CE, UL, cULus |
| Humidity |
90 % (non-condensing) |
Values follow the Phoenix Contact Soft Starter specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Soft Starter variants |
| Catalog number |
Overload capacity |
Frequency |
|
1201695 (this page) |
150 % for 60 s (IEC 61800-2) |
50/60 Hz (IEC 61800-2) |
| 1201694 |
150 % for 60 s (IEC 61800-2) |
50/60 Hz (IEC 61800-2) |
| 1201135 |
150 % for 60 s (IEC 61800-2) |
50/60 Hz (IEC 61800-2) |
| 2297523 |
150 % for 60 s (IEC 61800-2) |
50/60 Hz (IEC 61800-2) |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The 1201695 is the device-level element in a Phoenix Contact variable-frequency drive installation. It receives the field signals and control supply listed above — 1-phase 200...240 V / 3-phase 380...480 V AC — and switches or conditions the load within the 2.8 A (no line reactor) ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in pump sets, conveyor belts, fan and compressor drives, where the unit is matched to the original catalog number and the enclosure provides DIN rail mounting support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 1201695
Phoenix Contact 1201695 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 1201695; confirm the installed unit's part number and revision so the replacement matches both electrically and mechanically.
- Supply voltage: 1-phase 200...240 V / 3-phase 380...480 V AC — Use it as the reference when cross-checking a current-production equivalent.
- Operating temperature: -10...+60 °C (IEC 60068-2-1) — Verify it in the project documentation before confirming the order.
- Tripping characteristic: 10 mm — Check this value against the nameplate of the installed unit before ordering.
- Humidity: 90 % (non-condensing) — Match it to the existing panel and upstream protection.
Available from stock with datasheet, certificates and a quotation on request.
Common questions about 1201695
Q.Before ordering 1201695, which overload capacity entry should be checked?
The overload capacity entry quoted above is 150 % for 60 s (IEC 61800-2). Check the revision of the installed unit if the catalog number has been superseded.
Q.Where can I find the control method data for 1201695?
It is listed in the specification table for Phoenix Contact 1201695 as V/f, sensorless vector (IEC 61800-2). Compare it with the nameplate of the installed unit before ordering.
Q.For 1201695, what does the specification table state about humidity?
The specification table lists humidity = 90 % (non-condensing) for Phoenix Contact 1201695. Confirm this figure against the unit currently in the panel.
Q.Can the 1201695 replace the unit currently installed in my panel?
Compare catalog number 1201695 and the ratings above with the nameplate of the installed device. A current-production equivalent is selected by function and electrical rating, not by the label alone.
Q.What should I include in an enquiry for 1201695?
Send the full catalog number 1201695, the required quantity and a photo of the nameplate. Stock, lead time and the applicable compliance documents can then be confirmed for Phoenix Contact 1201695.