Phoenix Contact · Soft Starter
1201694 is a Phoenix Contact variable-frequency drive with Overload capacity 150 % for 60 s (IEC 61800-2); Enclosure rating IP20 (IEC 60529); Frequency 50/60 Hz (IEC 61800-2). It is used in pump sets, conveyor belts, fan and compressor drives where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Overload capacity150 % for 60 s (IEC 61800-2)
-
Enclosure ratingIP20 (IEC 60529)
-
Frequency50/60 Hz (IEC 61800-2)
-
Rated current Ie2 A (no line reactor)
Specifications
| Electrical |
| Rated current Ie |
2 A (no line reactor) |
| Tripping characteristic |
10 mm |
| Supply voltage |
1-phase 200...240 V / 3-phase 380...480 V AC |
| Input voltage range |
380 V AC |
| Output current |
≤ 2.7 A (180 s) |
| Frequency |
50/60 Hz (IEC 61800-2) |
| Control method |
V/f, sensorless vector (IEC 61800-2) |
| Overload capacity |
150 % for 60 s (IEC 61800-2) |
| Mechanical |
| Weight |
1,225 g |
| Mounting |
DIN rail mounting |
| Terminal wire size |
0.2 mm² ... 6 mm² |
| Enclosure rating |
IP20 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
-10...+60 °C (IEC 60068-2-1) |
| Certifications |
CE, UL, cULus |
| Humidity |
90 % (non-condensing) |
Values follow the Phoenix Contact Soft Starter specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Soft Starter variants |
| Catalog number |
Overload capacity |
Frequency |
|
1201694 (this page) |
150 % for 60 s (IEC 61800-2) |
50/60 Hz (IEC 61800-2) |
| 1201695 |
150 % for 60 s (IEC 61800-2) |
50/60 Hz (IEC 61800-2) |
| 1201135 |
150 % for 60 s (IEC 61800-2) |
50/60 Hz (IEC 61800-2) |
| 2297523 |
150 % for 60 s (IEC 61800-2) |
50/60 Hz (IEC 61800-2) |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The 1201694 is the device-level element in a Phoenix Contact variable-frequency drive installation. It receives the field signals and control supply listed above — 1-phase 200...240 V / 3-phase 380...480 V AC — and switches or conditions the load within the 2 A (no line reactor) ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in pump sets, conveyor belts, fan and compressor drives, where the unit is matched to the original catalog number and the enclosure provides DIN rail mounting support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 1201694
Phoenix Contact 1201694 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 1201694; verify the catalog number against your bill of materials before requesting a quotation.
- Control method: V/f, sensorless vector (IEC 61800-2) — Match it to the existing panel and upstream protection.
- Humidity: 90 % (non-condensing) — Record it with the other nameplate data when sourcing a replacement.
- Overload capacity: 150 % for 60 s (IEC 61800-2) — Confirm the revision of the installed unit before a like-for-like replacement.
- Rated current Ie: 2 A (no line reactor) — Use it as the reference when cross-checking a current-production equivalent.
Cross-check the ratings above with the installed device before confirming the order.
Common questions about 1201694
Q.Before ordering 1201694, which tripping characteristic entry should be checked?
The tripping characteristic entry quoted above is 10 mm. Use the value as the reference when sourcing a current-production equivalent.
Q.Where can I find the supply voltage data for 1201694?
It is listed in the specification table for Phoenix Contact 1201694 as 1-phase 200...240 V / 3-phase 380...480 V AC. Check the revision of the installed unit if the catalog number has been superseded.
Q.For 1201694, what does the specification table state about enclosure rating?
The specification table lists enclosure rating = IP20 (IEC 60529) for Phoenix Contact 1201694. Compare it with the nameplate of the installed unit before ordering.
Q.How do I confirm compatibility of 1201694 before ordering?
Match the catalog number 1201694 and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.
Q.Can the 1201694 replace the unit currently installed in my panel?
Compare catalog number 1201694 and the ratings above with the nameplate of the installed device. A current-production equivalent is selected by function and electrical rating, not by the label alone.