Phoenix Contact · Temperature measuring transducer
1050252 is a Phoenix Contact power supply with Output voltage 6 V; Output current 16.6 mA (RTD in 4-conductor technology); Supply voltage 24 V DC -20 % ... +25 %. It is used in DIN-rail control cabinets, sensor and relay supplies, backplane bus power where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Output voltage6 V
-
Output current16.6 mA (RTD in 4-conductor technology)
-
Supply voltage24 V DC -20 % ... +25 %
-
Enclosure ratingIP20 (IEC 60529)
Specifications
| Electrical |
| Tripping characteristic |
10 mm |
| Supply voltage |
24 V DC -20 % ... +25 % |
| Output voltage |
6 V |
| Output current |
16.6 mA (RTD in 4-conductor technology) |
| Power consumption |
≤ 1 W |
| I/O and communication |
| Response time |
≤ 1.7 s (with filter factor = 1) |
| Mechanical |
| Weight |
169 g |
| Mounting |
DIN rail / panel |
| Terminal wire size |
50 Ω (Per cable) |
| Enclosure rating |
IP20 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
0...+55 °C (IEC 60068-2-1) |
| Certifications |
CE, UL, cULus |
| Humidity |
5 % ... 95 % (non-condensing) |
Values follow the Phoenix Contact Temperature measuring transducer specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Where it sits in the control system
The 1050252 is the device-level element in a Phoenix Contact power supply installation. It receives the field signals and control supply listed above — 24 V DC -20 % ... +25 % — and switches or conditions the load within the the rated ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in DIN-rail control cabinets, sensor and relay supplies, backplane bus power, where the unit is matched to the original catalog number and the enclosure provides DIN rail / panel support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 1050252
Phoenix Contact 1050252 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 1050252; confirm the installed unit's part number and revision so the replacement matches both electrically and mechanically.
- Power consumption: ≤ 1 W — Confirm the revision of the installed unit before a like-for-like replacement.
- Enclosure rating: IP20 (IEC 60529) — Use it as the reference when cross-checking a current-production equivalent.
- Tripping characteristic: 10 mm — Verify it in the project documentation before confirming the order.
- Response time: ≤ 1.7 s (with filter factor = 1) — Check this value against the nameplate of the installed unit before ordering.
Datasheets and compliance documents are available on request; quote the full catalog number when enquiring.
Common questions about 1050252
Q.Which value is published under response time for catalog number 1050252?
For 1050252, response time is given as ≤ 1.7 s (with filter factor = 1). Confirm this figure against the unit currently in the panel.
Q.Before ordering 1050252, which enclosure rating entry should be checked?
The enclosure rating entry quoted above is IP20 (IEC 60529). Use the value as the reference when sourcing a current-production equivalent.
Q.Where can I find the weight data for 1050252?
It is listed in the specification table for Phoenix Contact 1050252 as 169 g. Check the revision of the installed unit if the catalog number has been superseded.
Q.Can the 1050252 replace the unit currently installed in my panel?
Compare catalog number 1050252 and the ratings above with the nameplate of the installed device. A current-production equivalent is selected by function and electrical rating, not by the label alone.
Q.How do I confirm compatibility of 1050252 before ordering?
Match the catalog number 1050252 and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.