Phoenix Contact · Terminal Block
0920083 is a Phoenix Contact circuit breaker with Rated current Ie up to 41 A (IEC 60947-7-1); Tripping characteristic 13 mm; Rated operational voltage 800 V (IEC 60947-7-1). It is used in distribution boards, motor protection circuits, panel feeders where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Rated current Ieup to 41 A (IEC 60947-7-1)
-
Tripping characteristic13 mm
-
Rated operational voltage800 V (IEC 60947-7-1)
-
Mounting35 mm DIN rail (IEC 60715)
Specifications
| Electrical |
| Rated current Ie |
up to 41 A (IEC 60947-7-1) |
| Rated operational voltage |
800 V (IEC 60947-7-1) |
| Tripping characteristic |
13 mm |
| Rated torque |
1.5 ... 1.8 Nm |
| Mechanical |
| Weight |
28.018 g |
| Mounting |
35 mm DIN rail (IEC 60715) |
| Terminal wire size |
0.5 mm² ... 16 mm² |
| Environment and compliance |
| Operating temperature |
-25 °C ... 60 °C (for a short time, not exceeding 24 h, -60 °C to +70 °C) |
| Certifications |
CE, UL, cULus |
| Humidity |
20 % ... 90 % |
Values follow the Phoenix Contact Terminal Block specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Terminal Block variants |
| Catalog number |
Tripping characteristic |
Rated operational voltage |
|
0920083 (this page) |
13 mm |
800 V (IEC 60947-7-1) |
| 0270018 |
9 mm |
800 V (IEC 60947-7-1) |
| 0313085 |
11 mm |
800 V (IEC 60947-7-1) |
| 0404017 |
16 mm |
800 V (IEC 60947-7-1) |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The 0920083 is the device-level element in a Phoenix Contact circuit breaker installation. It receives the field signals and control supply listed above — 800 V (IEC 60947-7-1) — and switches or conditions the load within the up to 41 A (IEC 60947-7-1) ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in distribution boards, motor protection circuits, panel feeders, where the unit is matched to the original catalog number and the enclosure provides 35 mm DIN rail (IEC 60715) support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 0920083
Phoenix Contact 0920083 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 0920083; verify the catalog number against your bill of materials before requesting a quotation.
- Rated operational voltage: 800 V (IEC 60947-7-1) — Check this value against the nameplate of the installed unit before ordering.
- Mounting: 35 mm DIN rail (IEC 60715) — Match it to the existing panel and upstream protection.
- Terminal wire size: 0.5 mm² ... 16 mm² — Record it with the other nameplate data when sourcing a replacement.
- Weight: 28.018 g — Confirm the revision of the installed unit before a like-for-like replacement.
Available from stock with datasheet, certificates and a quotation on request.
Common questions about 0920083
Q.For 0920083, what does the specification table state about weight?
The specification table lists weight = 28.018 g for Phoenix Contact 0920083. Check the revision of the installed unit if the catalog number has been superseded.
Q.Which value is published under terminal wire size for catalog number 0920083?
For 0920083, terminal wire size is given as 0.5 mm² ... 16 mm². Compare it with the nameplate of the installed unit before ordering.
Q.Before ordering 0920083, which mounting entry should be checked?
The mounting entry quoted above is 35 mm DIN rail (IEC 60715). Confirm this figure against the unit currently in the panel.
Q.What should I include in an enquiry for 0920083?
Send the full catalog number 0920083, the required quantity and a photo of the nameplate. Stock, lead time and the applicable compliance documents can then be confirmed for Phoenix Contact 0920083.
Q.How do I confirm compatibility of 0920083 before ordering?
Match the catalog number 0920083 and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.