Phoenix Contact · Terminal Block
0711344 is a Phoenix Contact circuit breaker with Rated current Ie up to 41 A (IEC 60947-7-1); Tripping characteristic 8 mm; Rated operational voltage 800 V (IEC 60947-7-1). It is used in distribution boards, motor protection circuits, panel feeders where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Rated current Ieup to 41 A (IEC 60947-7-1)
-
Tripping characteristic8 mm
-
Rated operational voltage800 V (IEC 60947-7-1)
-
Mounting35 mm DIN rail (IEC 60715)
Specifications
| Electrical |
| Rated current Ie |
up to 41 A (IEC 60947-7-1) |
| Rated operational voltage |
800 V (IEC 60947-7-1) |
| Tripping characteristic |
8 mm |
| Frequency |
f1= 5 Hz to f2= 250 Hz |
| Rated torque |
0.6 ... 0.8 Nm |
| Rated speed |
10 (+/- 2) rpm |
| Mechanical |
| Weight |
0.2 mm² / 0.2 kg |
| Mounting |
35 mm DIN rail (IEC 60715) |
| Terminal wire size |
0.2 mm² ... 6 mm² |
| Environment and compliance |
| Operating temperature |
-25 °C ... 60 °C (for a short time, not exceeding 24 h, -60 °C to +70 °C) |
| Certifications |
CE, UL, cULus |
| Humidity |
20 % ... 90 % |
Values follow the Phoenix Contact Terminal Block specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Terminal Block variants |
| Catalog number |
Tripping characteristic |
Rated operational voltage |
|
0711344 (this page) |
8 mm |
800 V (IEC 60947-7-1) |
| 0711852 |
40 mm |
800 V (IEC 60947-7-1) |
| 0701082 |
15 mm |
800 V (IEC 60947-7-1) |
| 0704076 |
15 mm |
800 V (IEC 60947-7-1) |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The 0711344 is the device-level element in a Phoenix Contact circuit breaker installation. It receives the field signals and control supply listed above — 800 V (IEC 60947-7-1) — and switches or conditions the load within the up to 41 A (IEC 60947-7-1) ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in distribution boards, motor protection circuits, panel feeders, where the unit is matched to the original catalog number and the enclosure provides 35 mm DIN rail (IEC 60715) support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 0711344
Phoenix Contact 0711344 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 0711344; always cross-check the catalog number and hardware revision on the nameplate before placing an order.
- Weight: 0.2 mm² / 0.2 kg — Use it as the reference when cross-checking a current-production equivalent.
- Mounting: 35 mm DIN rail (IEC 60715) — Verify it in the project documentation before confirming the order.
- Operating temperature: -25 °C ... 60 °C (for a short time, not exceeding 24 h, -60 °C to +70 °C) — Check this value against the nameplate of the installed unit before ordering.
- Frequency: f1= 5 Hz to f2= 250 Hz — Match it to the existing panel and upstream protection.
Cross-check the ratings above with the installed device before confirming the order.
Common questions about 0711344
Q.Which value is published under tripping characteristic for catalog number 0711344?
For 0711344, tripping characteristic is given as 8 mm. Check the revision of the installed unit if the catalog number has been superseded.
Q.Before ordering 0711344, which frequency entry should be checked?
The frequency entry quoted above is f1= 5 Hz to f2= 250 Hz. Compare it with the nameplate of the installed unit before ordering.
Q.Where can I find the operating temperature data for 0711344?
It is listed in the specification table for Phoenix Contact 0711344 as -25 °C ... 60 °C (for a short time, not exceeding 24 h, -60 °C to +70 °C). Confirm this figure against the unit currently in the panel.
Q.How do I confirm compatibility of 0711344 before ordering?
Match the catalog number 0711344 and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.
Q.What should I include in an enquiry for 0711344?
Send the full catalog number 0711344, the required quantity and a photo of the nameplate. Stock, lead time and the applicable compliance documents can then be confirmed for Phoenix Contact 0711344.