Phoenix Contact · Terminal Block
0701082 is a Phoenix Contact circuit breaker with Rated current Ie up to 41 A (IEC 60947-7-1); Tripping characteristic 15 mm; Rated operational voltage 800 V (IEC 60947-7-1). It is used in distribution boards, motor protection circuits, panel feeders where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Rated current Ieup to 41 A (IEC 60947-7-1)
-
Tripping characteristic15 mm
-
Rated operational voltage800 V (IEC 60947-7-1)
-
Mounting35 mm DIN rail (IEC 60715)
Specifications
| Electrical |
| Rated current Ie |
up to 41 A (IEC 60947-7-1) |
| Rated operational voltage |
800 V (IEC 60947-7-1) |
| Tripping characteristic |
15 mm |
| Frequency |
f1= 5 Hz to f2= 250 Hz |
| Rated torque |
1.5 ... 1.8 Nm |
| Mechanical |
| Weight |
32.47 g |
| Mounting |
35 mm DIN rail (IEC 60715) |
| Terminal wire size |
0.5 mm² ... 16 mm² |
| Environment and compliance |
| Operating temperature |
-25 °C ... 60 °C (for a short time, not exceeding 24 h, -60 °C to +70 °C) |
| Certifications |
CE, UL, cULus |
| Humidity |
30 % ... 70 % |
Values follow the Phoenix Contact Terminal Block specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Terminal Block variants |
| Catalog number |
Tripping characteristic |
Rated operational voltage |
|
0701082 (this page) |
15 mm |
800 V (IEC 60947-7-1) |
| 0704076 |
15 mm |
800 V (IEC 60947-7-1) |
| 0711344 |
8 mm |
800 V (IEC 60947-7-1) |
| 0711852 |
40 mm |
800 V (IEC 60947-7-1) |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The 0701082 is the device-level element in a Phoenix Contact circuit breaker installation. It receives the field signals and control supply listed above — 800 V (IEC 60947-7-1) — and switches or conditions the load within the up to 41 A (IEC 60947-7-1) ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in distribution boards, motor protection circuits, panel feeders, where the unit is matched to the original catalog number and the enclosure provides 35 mm DIN rail (IEC 60715) support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 0701082
Phoenix Contact 0701082 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 0701082; confirm the installed unit's part number and revision so the replacement matches both electrically and mechanically.
- Tripping characteristic: 15 mm — Use it as the reference when cross-checking a current-production equivalent.
- Weight: 32.47 g — Verify it in the project documentation before confirming the order.
- Rated operational voltage: 800 V (IEC 60947-7-1) — Check this value against the nameplate of the installed unit before ordering.
- Rated torque: 1.5 ... 1.8 Nm — Match it to the existing panel and upstream protection.
Datasheets and compliance documents are available on request; quote the full catalog number when enquiring.
Common questions about 0701082
Q.Where can I find the rated torque data for 0701082?
It is listed in the specification table for Phoenix Contact 0701082 as 1.5 ... 1.8 Nm. Use the value as the reference when sourcing a current-production equivalent.
Q.For 0701082, what does the specification table state about certifications?
The specification table lists certifications = CE, UL, cULus for Phoenix Contact 0701082. Check the revision of the installed unit if the catalog number has been superseded.
Q.Which value is published under rated operational voltage for catalog number 0701082?
For 0701082, rated operational voltage is given as 800 V (IEC 60947-7-1). Compare it with the nameplate of the installed unit before ordering.
Q.How do I confirm compatibility of 0701082 before ordering?
Match the catalog number 0701082 and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.
Q.Can the 0701082 replace the unit currently installed in my panel?
Compare catalog number 0701082 and the ratings above with the nameplate of the installed device. A current-production equivalent is selected by function and electrical rating, not by the label alone.