Phoenix Contact · Energy Meter
2907983 is a Phoenix Contact circuit breaker with Tripping characteristic 8 mm; Breaking capacity Icu/Ics up to 63rd harmonic; Supply voltage 100 V AC ... 230 V AC (±20 %). It is used in distribution boards, motor protection circuits, panel feeders where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Tripping characteristic8 mm
-
Breaking capacity Icu/Icsup to 63rd harmonic
-
Supply voltage100 V AC ... 230 V AC (±20 %)
-
Enclosure ratingIP20 (IEC 60529)
Specifications
| Electrical |
| Breaking capacity Icu/Ics |
up to 63rd harmonic |
| Tripping characteristic |
8 mm |
| Supply voltage |
100 V AC ... 230 V AC (±20 %) |
| Input voltage range |
18 V AC ... 690 V AC (Phase/Phase) |
| Power consumption |
≤ 4 W |
| Frequency |
50 Hz ... 60 Hz (AC sine) |
| Overload capacity |
6 A (I max ) |
| Rated torque |
0.5 Nm ... 0.6 Nm |
| Rated speed |
10 Mbps |
| I/O and communication |
| Response time |
10 mA (1 A) |
| Mechanical |
| Weight |
329 g |
| Mounting |
DIN rail / panel |
| Terminal wire size |
0.2 mm² ... 6 mm² |
| Enclosure rating |
IP20 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
0...+55 °C (IEC 60068-2-1) |
| Certifications |
CE, UL, cULus |
| Humidity |
≤ 95 % (non-condensing) |
Values follow the Phoenix Contact Energy Meter specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Energy Meter variants |
| Catalog number |
Tripping characteristic |
Breaking capacity Icu/Ics |
|
2907983 (this page) |
8 mm |
up to 63rd harmonic |
| 2907980 |
8 mm |
up to 63rd harmonic |
| 2907945 |
8 mm |
up to 63rd harmonic |
| 2907946 |
8 mm |
up to 63rd harmonic |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The 2907983 is the device-level element in a Phoenix Contact circuit breaker installation. It receives the field signals and control supply listed above — 100 V AC ... 230 V AC (±20 %) — and switches or conditions the load within the the rated ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in distribution boards, motor protection circuits, panel feeders, where the unit is matched to the original catalog number and the enclosure provides DIN rail / panel support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 2907983
Phoenix Contact 2907983 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 2907983; confirm the installed unit's part number and revision so the replacement matches both electrically and mechanically.
- Power consumption: ≤ 4 W — Confirm the revision of the installed unit before a like-for-like replacement.
- Breaking capacity Icu/Ics: up to 63rd harmonic — Use it as the reference when cross-checking a current-production equivalent.
- Tripping characteristic: 8 mm — Verify it in the project documentation before confirming the order.
- Response time: 10 mA (1 A) — Check this value against the nameplate of the installed unit before ordering.
Datasheets and compliance documents are available on request; quote the full catalog number when enquiring.
Common questions about 2907983
Q.For 2907983, what does the specification table state about breaking capacity Icu/Ics?
The specification table lists breaking capacity Icu/Ics = up to 63rd harmonic for Phoenix Contact 2907983. Check the revision of the installed unit if the catalog number has been superseded.
Q.Which value is published under rated speed for catalog number 2907983?
For 2907983, rated speed is given as 10 Mbps. Compare it with the nameplate of the installed unit before ordering.
Q.Before ordering 2907983, which frequency entry should be checked?
The frequency entry quoted above is 50 Hz ... 60 Hz (AC sine). Confirm this figure against the unit currently in the panel.
Q.How do I confirm compatibility of 2907983 before ordering?
Match the catalog number 2907983 and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.
Q.Can the 2907983 replace the unit currently installed in my panel?
Compare catalog number 2907983 and the ratings above with the nameplate of the installed device. A current-production equivalent is selected by function and electrical rating, not by the label alone.