Phoenix Contact · Terminal Block
1804917 is a Phoenix Contact circuit breaker with Rated current Ie up to 41 A (IEC 60947-7-1); Tripping characteristic 7 mm; Rated operational voltage 800 V (IEC 60947-7-1). It is used in distribution boards, motor protection circuits, panel feeders where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Rated current Ieup to 41 A (IEC 60947-7-1)
-
Tripping characteristic7 mm
-
Rated operational voltage800 V (IEC 60947-7-1)
-
Breaking capacity Icu/Icshot-dip tin-plated
Specifications
| Electrical |
| Rated current Ie |
up to 41 A (IEC 60947-7-1) |
| Rated operational voltage |
800 V (IEC 60947-7-1) |
| Rated insulation voltage Ui |
400 V |
| Rated impulse withstand Uimp |
7.3 kV |
| Breaking capacity Icu/Ics |
hot-dip tin-plated |
| Tripping characteristic |
7 mm |
| Frequency |
3.31 kV |
| Rated torque |
0.5 Nm ... 0.6 Nm |
| Rated speed |
1 octave/min |
| Mechanical |
| Weight |
12.935 g |
| Mounting |
35 mm DIN rail (IEC 60715) |
| Terminal type |
Tin (4 µm - 8 µm Sn) |
| Terminal wire size |
0 ° |
| Environment and compliance |
| Operating temperature |
-40 °C ... 70 °C |
| Certifications |
CE, UL, cULus |
| Humidity |
30 % ... 70 % |
Values follow the Phoenix Contact Terminal Block specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Terminal Block variants |
| Catalog number |
Breaking capacity Icu/Ics |
Rated operational voltage |
|
1804917 (this page) |
hot-dip tin-plated |
800 V (IEC 60947-7-1) |
| 1803332 |
Tin-plated |
800 V (IEC 60947-7-1) |
| 1803358 |
Tin-plated |
800 V (IEC 60947-7-1) |
| 1803374 |
Tin-plated |
800 V (IEC 60947-7-1) |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The 1804917 is the device-level element in a Phoenix Contact circuit breaker installation. It receives the field signals and control supply listed above — 800 V (IEC 60947-7-1) — and switches or conditions the load within the up to 41 A (IEC 60947-7-1) ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in distribution boards, motor protection circuits, panel feeders, where the unit is matched to the original catalog number and the enclosure provides 35 mm DIN rail (IEC 60715) support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 1804917
Phoenix Contact 1804917 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 1804917; record the nameplate data of the unit being replaced before selecting an equivalent.
- Mounting: 35 mm DIN rail (IEC 60715) — Verify it in the project documentation before confirming the order.
- Terminal type: Tin (4 µm - 8 µm Sn) — Check this value against the nameplate of the installed unit before ordering.
- Weight: 12.935 g — Match it to the existing panel and upstream protection.
- Terminal wire size: 0 ° — Record it with the other nameplate data when sourcing a replacement.
Cross-check the ratings above with the installed device before confirming the order.
Common questions about 1804917
Q.Before ordering 1804917, which breaking capacity Icu/Ics entry should be checked?
The breaking capacity Icu/Ics entry quoted above is hot-dip tin-plated. Compare it with the nameplate of the installed unit before ordering.
Q.Where can I find the terminal wire size data for 1804917?
It is listed in the specification table for Phoenix Contact 1804917 as 0 °. Confirm this figure against the unit currently in the panel.
Q.For 1804917, what does the specification table state about rated impulse withstand Uimp?
The specification table lists rated impulse withstand Uimp = 7.3 kV for Phoenix Contact 1804917. Use the value as the reference when sourcing a current-production equivalent.
Q.What should I include in an enquiry for 1804917?
Send the full catalog number 1804917, the required quantity and a photo of the nameplate. Stock, lead time and the applicable compliance documents can then be confirmed for Phoenix Contact 1804917.
Q.How do I confirm compatibility of 1804917 before ordering?
Match the catalog number 1804917 and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.