Phoenix Contact · Power Distributor
1516810 is a Phoenix Contact circuit breaker with Rated current Ie 10 A; Tripping characteristic 7 mm; Breaking capacity Icu/Ics Supply voltage per module Green LED. It is used in distribution boards, motor protection circuits, panel feeders where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Rated current Ie10 A
-
Tripping characteristic7 mm
-
Breaking capacity Icu/IcsSupply voltage per module Green LED
-
Enclosure ratingIP20 (IEC 60529)
Specifications
| Electrical |
| Rated current Ie |
10 A |
| Breaking capacity Icu/Ics |
Supply voltage per module Green LED |
| Tripping characteristic |
7 mm |
| Input voltage range |
85...264 V AC / 110...300 V DC (IEC 61010) |
| Efficiency |
up to 94 % |
| Rated torque |
0.35 Nm |
| Mechanical |
| Weight |
310 g |
| Mounting |
35 mm DIN rail (IEC 60715) |
| Terminal wire size |
0.14 mm² ... 1.5 mm² |
| Enclosure rating |
IP20 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
-25...+70 °C (IEC 60068-2-1) |
| Certifications |
CE, UL, cULus |
Values follow the Phoenix Contact Power Distributor specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Power Distributor variants |
| Catalog number |
Breaking capacity Icu/Ics |
Tripping characteristic |
|
1516810 (this page) |
Supply voltage per module Green LED |
7 mm |
| 1516881 |
— |
7 mm |
| 1516056 |
Supply voltage Green LED |
— |
| 1516111 |
Supply voltage Green LED |
— |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The 1516810 is the device-level element in a Phoenix Contact circuit breaker installation. It receives the field signals and control supply listed above — the rated supply — and switches or conditions the load within the 10 A ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in distribution boards, motor protection circuits, panel feeders, where the unit is matched to the original catalog number and the enclosure provides 35 mm DIN rail (IEC 60715) support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 1516810
Phoenix Contact 1516810 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 1516810; always cross-check the catalog number and hardware revision on the nameplate before placing an order.
- Terminal wire size: 0.14 mm² ... 1.5 mm² — Check this value against the nameplate of the installed unit before ordering.
- Enclosure rating: IP20 (IEC 60529) — Match it to the existing panel and upstream protection.
- Input voltage range: 85...264 V AC / 110...300 V DC (IEC 61010) — Record it with the other nameplate data when sourcing a replacement.
- Operating temperature: -25...+70 °C (IEC 60068-2-1) — Confirm the revision of the installed unit before a like-for-like replacement.
Cross-check the ratings above with the installed device before confirming the order.
Common questions about 1516810
Q.Before ordering 1516810, which tripping characteristic entry should be checked?
The tripping characteristic entry quoted above is 7 mm. Compare it with the nameplate of the installed unit before ordering.
Q.Where can I find the input voltage range data for 1516810?
It is listed in the specification table for Phoenix Contact 1516810 as 85...264 V AC / 110...300 V DC (IEC 61010). Confirm this figure against the unit currently in the panel.
Q.For 1516810, what does the specification table state about breaking capacity Icu/Ics?
The specification table lists breaking capacity Icu/Ics = Supply voltage per module Green LED for Phoenix Contact 1516810. Use the value as the reference when sourcing a current-production equivalent.
Q.How do I confirm compatibility of 1516810 before ordering?
Match the catalog number 1516810 and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.
Q.Can the 1516810 replace the unit currently installed in my panel?
Compare catalog number 1516810 and the ratings above with the nameplate of the installed device. A current-production equivalent is selected by function and electrical rating, not by the label alone.