Phoenix Contact · Connection Cable
1430682 is a Phoenix Contact connection cable with Rated current Ie up to 4 A; Enclosure rating IP67 (IEC 60529); Operating temperature -25...+80 °C (IEC 60068-2-1). It is used in control panels, machine builds, spare-part replacements where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Rated current Ieup to 4 A
-
Enclosure ratingIP67 (IEC 60529)
-
Operating temperature-25...+80 °C (IEC 60068-2-1)
-
CertificationsCE, UL, cULus
Specifications
| Electrical |
| Rated current Ie |
up to 4 A |
| Rated torque |
0.4 Nm (M12 connector) |
| I/O and communication |
| Flame detection |
in acc. to UL VW1 |
| Mechanical |
| Weight |
17 kg/km |
| Terminal wire size |
18x 0.10 mm |
| Enclosure rating |
IP67 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
-25...+80 °C (IEC 60068-2-1) |
| Certifications |
CE, UL, cULus |
Values follow the Phoenix Contact Connection Cable specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Connection Cable variants |
| Catalog number |
Rated current Ie |
|
1430682 (this page) |
up to 4 A |
| 1430679 |
up to 4 A |
| 1430064 |
up to 4 A |
| 1430077 |
up to 4 A |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The 1430682 is the device-level element in a Phoenix Contact connection cable installation. It receives the field signals and control supply listed above — the rated supply — and switches or conditions the load within the up to 4 A ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in control panels, machine builds, spare-part replacements, where the unit is matched to the original catalog number and the enclosure provides standard panel or DIN-rail support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 1430682
Phoenix Contact 1430682 — Sensor or detector for object detection, distance measurement and status feedback on production lines. The figures below are taken from the specification table on this page for catalog number 1430682; record the nameplate data of the unit being replaced before selecting an equivalent.
- Enclosure rating: IP67 (IEC 60529) — Verify it in the project documentation before confirming the order.
- Rated torque: 0.4 Nm (M12 connector) — Check this value against the nameplate of the installed unit before ordering.
- Terminal wire size: 18x 0.10 mm — Match it to the existing panel and upstream protection.
- Flame detection: in acc. to UL VW1 — Record it with the other nameplate data when sourcing a replacement.
Cross-check the ratings above with the installed device before confirming the order.
Common questions about 1430682
Q.For 1430682, what does the specification table state about operating temperature?
The specification table lists operating temperature = -25...+80 °C (IEC 60068-2-1) for Phoenix Contact 1430682. Check the revision of the installed unit if the catalog number has been superseded.
Q.Which value is published under certifications for catalog number 1430682?
For 1430682, certifications is given as CE, UL, cULus. Compare it with the nameplate of the installed unit before ordering.
Q.Before ordering 1430682, which enclosure rating entry should be checked?
The enclosure rating entry quoted above is IP67 (IEC 60529). Confirm this figure against the unit currently in the panel.
Q.What should I include in an enquiry for 1430682?
Send the full catalog number 1430682, the required quantity and a photo of the nameplate. Stock, lead time and the applicable compliance documents can then be confirmed for Phoenix Contact 1430682.
Q.How do I confirm compatibility of 1430682 before ordering?
Match the catalog number 1430682 and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.