Phoenix Contact · Connection Cable
1080745 is a Phoenix Contact circuit breaker with Rated current Ie up to 4 A; Breaking capacity Icu/Ics CAT6A; Enclosure rating IP67 (IEC 60529). It is used in distribution boards, motor protection circuits, panel feeders where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Rated current Ieup to 4 A
-
Breaking capacity Icu/IcsCAT6A
-
Enclosure ratingIP67 (IEC 60529)
-
Operating temperature-25...+80 °C (IEC 60068-2-1)
Specifications
| Electrical |
| Rated current Ie |
up to 4 A |
| Breaking capacity Icu/Ics |
CAT6A |
| Rated torque |
0.4 Nm (M12 connector) |
| Rated speed |
10 Gbps |
| I/O and communication |
| Bus interface |
Ethernet |
| Flame detection |
according to IEC 60332-1-2 |
| Mechanical |
| Dimensions (H x W x D) |
Pin assignment of M12 plug, 8-pos., X-coded, pin side view |
| Weight |
507.8 g |
| Terminal wire size |
4x2xAWG26/7; S/FTP |
| Enclosure rating |
IP67 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
-25...+80 °C (IEC 60068-2-1) |
| Certifications |
CE, UL, cULus |
Values follow the Phoenix Contact Connection Cable specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Connection Cable variants |
| Catalog number |
Mounting |
|
1080745 (this page) |
— |
| 1000042 |
— |
| 1027669 |
Rear mounting (M16 x 1.5, with flat nut) |
| 1095900 |
— |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The 1080745 is the device-level element in a Phoenix Contact circuit breaker installation. It receives the field signals and control supply listed above — the rated supply — and switches or conditions the load within the up to 4 A ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in distribution boards, motor protection circuits, panel feeders, where the unit is matched to the original catalog number and the enclosure provides standard panel or DIN-rail support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 1080745
Phoenix Contact 1080745 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 1080745; verify the catalog number against your bill of materials before requesting a quotation.
- Rated torque: 0.4 Nm (M12 connector) — Record it with the other nameplate data when sourcing a replacement.
- Rated speed: 10 Gbps — Confirm the revision of the installed unit before a like-for-like replacement.
- Flame detection: according to IEC 60332-1-2 — Use it as the reference when cross-checking a current-production equivalent.
- Weight: 507.8 g — Verify it in the project documentation before confirming the order.
Datasheets and compliance documents are available on request; quote the full catalog number when enquiring.
Common questions about 1080745
Q.Which value is published under certifications for catalog number 1080745?
For 1080745, certifications is given as CE, UL, cULus. Compare it with the nameplate of the installed unit before ordering.
Q.Before ordering 1080745, which rated speed entry should be checked?
The rated speed entry quoted above is 10 Gbps. Confirm this figure against the unit currently in the panel.
Q.Where can I find the rated torque data for 1080745?
It is listed in the specification table for Phoenix Contact 1080745 as 0.4 Nm (M12 connector). Use the value as the reference when sourcing a current-production equivalent.
Q.Can the 1080745 replace the unit currently installed in my panel?
Compare catalog number 1080745 and the ratings above with the nameplate of the installed device. A current-production equivalent is selected by function and electrical rating, not by the label alone.
Q.What should I include in an enquiry for 1080745?
Send the full catalog number 1080745, the required quantity and a photo of the nameplate. Stock, lead time and the applicable compliance documents can then be confirmed for Phoenix Contact 1080745.