Phoenix Contact · Power Meter
2906233 is a Phoenix Contact contactor with Rated current Ie 0 A AC ... 100 A AC; Coil voltage Elastollan; Supply voltage 100...240 V AC / 24 V DC. It is used in motor starters, pump control panels, HVAC contactor banks where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Rated current Ie0 A AC ... 100 A AC
-
Coil voltageElastollan
-
Supply voltage100...240 V AC / 24 V DC
-
Enclosure ratingIP20 (IEC 60529)
Specifications
| Electrical |
| Rated current Ie |
0 A AC ... 100 A AC |
| Rated insulation voltage Ui |
300 V |
| Tripping characteristic |
10 mm |
| Coil voltage |
Elastollan |
| Supply voltage |
100...240 V AC / 24 V DC |
| Output voltage |
V OUT = M * dI/dt |
| Power consumption |
≤ 1 W (at I OUT = 20 mA, 9.6 V DC, 600 Ω load) |
| Frequency |
16 Hz ... 1000 Hz |
| Rated torque |
0.5 Nm ... 0.6 Nm |
| I/O and communication |
| Response time |
110 ms |
| Mechanical |
| Weight |
478 g |
| Mounting |
DIN rail / panel |
| Terminal wire size |
2x 0.22 mm (Signal (tinned)) |
| Enclosure rating |
IP20 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
0...+55 °C (IEC 60068-2-1) |
| Certifications |
CE, UL, cULus |
| Humidity |
5 % ... 95 % (non-condensing) |
Values follow the Phoenix Contact Power Meter specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Power Meter variants |
| Catalog number |
Coil voltage |
Rated current Ie |
|
2906233 (this page) |
Elastollan |
0 A AC ... 100 A AC |
| 2906235 |
Elastollan |
0 A AC ... 100 A AC |
| 2906236 |
Elastollan |
0 A AC ... 100 A AC |
| 2904921 |
Elastollan |
0 A AC ... 100 A AC |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The 2906233 is the device-level element in a Phoenix Contact contactor installation. It receives the field signals and control supply listed above — 100...240 V AC / 24 V DC — and switches or conditions the load within the 0 A AC ... 100 A AC ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in motor starters, pump control panels, HVAC contactor banks, where the unit is matched to the original catalog number and the enclosure provides DIN rail / panel support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 2906233
Phoenix Contact 2906233 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 2906233; record the nameplate data of the unit being replaced before selecting an equivalent.
- Frequency: 16 Hz ... 1000 Hz — Use it as the reference when cross-checking a current-production equivalent.
- Response time: 110 ms — Verify it in the project documentation before confirming the order.
- Enclosure rating: IP20 (IEC 60529) — Check this value against the nameplate of the installed unit before ordering.
- Rated current Ie: 0 A AC ... 100 A AC — Match it to the existing panel and upstream protection.
Available from stock with datasheet, certificates and a quotation on request.
Common questions about 2906233
Q.Before ordering 2906233, which weight entry should be checked?
The weight entry quoted above is 478 g. Compare it with the nameplate of the installed unit before ordering.
Q.Where can I find the rated insulation voltage Ui data for 2906233?
It is listed in the specification table for Phoenix Contact 2906233 as 300 V. Confirm this figure against the unit currently in the panel.
Q.For 2906233, what does the specification table state about supply voltage?
The specification table lists supply voltage = 100...240 V AC / 24 V DC for Phoenix Contact 2906233. Use the value as the reference when sourcing a current-production equivalent.
Q.What should I include in an enquiry for 2906233?
Send the full catalog number 2906233, the required quantity and a photo of the nameplate. Stock, lead time and the applicable compliance documents can then be confirmed for Phoenix Contact 2906233.
Q.How do I confirm compatibility of 2906233 before ordering?
Match the catalog number 2906233 and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.