Phoenix Contact · Temperature Transmitter
2902000 is a Phoenix Contact industrial component with Supply voltage 11...30 V DC (loop powered); Enclosure rating IP66 / IP67 (IEC 60529); Operating temperature -40...+85 °C (IEC 60068-2-1). It is used in control panels, machine builds, spare-part replacements where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Supply voltage11...30 V DC (loop powered)
-
Enclosure ratingIP66 / IP67 (IEC 60529)
-
Operating temperature-40...+85 °C (IEC 60068-2-1)
-
MountingDIN rail mounting
Specifications
| Electrical |
| Rated insulation voltage Ui |
300 V rms |
| Tripping characteristic |
10 mm |
| Supply voltage |
11...30 V DC (loop powered) |
| Power consumption |
≤ 200 mW (9.6 V DC) |
| Frequency |
30 Hz |
| Rated torque |
0.5 Nm ... 0.6 Nm |
| I/O and communication |
| Response time |
10 ms |
| Mechanical |
| Weight |
67.6 g |
| Mounting |
DIN rail mounting |
| Terminal wire size |
0.2 mm² ... 1.5 mm² (with ferrule) |
| Enclosure rating |
IP66 / IP67 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
-40...+85 °C (IEC 60068-2-1) |
| Certifications |
CE, UL, cULus |
| Humidity |
5 % ... 95 % (non-condensing) |
Values follow the Phoenix Contact Temperature Transmitter specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Temperature Transmitter variants |
| Catalog number |
Mounting |
|
2902000 (this page) |
DIN rail mounting |
| 2902001 |
DIN rail mounting |
| 2902002 |
DIN rail mounting |
| 2902003 |
DIN rail mounting |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The 2902000 is the device-level element in a Phoenix Contact industrial component installation. It receives the field signals and control supply listed above — 11...30 V DC (loop powered) — and switches or conditions the load within the the rated ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in control panels, machine builds, spare-part replacements, where the unit is matched to the original catalog number and the enclosure provides DIN rail mounting support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 2902000
Phoenix Contact 2902000 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 2902000; always cross-check the catalog number and hardware revision on the nameplate before placing an order.
- Weight: 67.6 g — Use it as the reference when cross-checking a current-production equivalent.
- Terminal wire size: 0.2 mm² ... 1.5 mm² (with ferrule) — Verify it in the project documentation before confirming the order.
- Mounting: DIN rail mounting — Check this value against the nameplate of the installed unit before ordering.
- Enclosure rating: IP66 / IP67 (IEC 60529) — Match it to the existing panel and upstream protection.
Datasheets and compliance documents are available on request; quote the full catalog number when enquiring.
Common questions about 2902000
Q.Before ordering 2902000, which rated insulation voltage Ui entry should be checked?
The rated insulation voltage Ui entry quoted above is 300 V rms. Check the revision of the installed unit if the catalog number has been superseded.
Q.Where can I find the supply voltage data for 2902000?
It is listed in the specification table for Phoenix Contact 2902000 as 11...30 V DC (loop powered). Compare it with the nameplate of the installed unit before ordering.
Q.For 2902000, what does the specification table state about operating temperature?
The specification table lists operating temperature = -40...+85 °C (IEC 60068-2-1) for Phoenix Contact 2902000. Confirm this figure against the unit currently in the panel.
Q.What should I include in an enquiry for 2902000?
Send the full catalog number 2902000, the required quantity and a photo of the nameplate. Stock, lead time and the applicable compliance documents can then be confirmed for Phoenix Contact 2902000.
Q.How do I confirm compatibility of 2902000 before ordering?
Match the catalog number 2902000 and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.