Phoenix Contact · Safety Relay
2700540 is a Phoenix Contact circuit breaker with Tripping characteristic 7 mm; Breaking capacity Icu/Ics no; Supply voltage 20.4 V DC ... 26.4 V DC. It is used in distribution boards, motor protection circuits, panel feeders where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Tripping characteristic7 mm
-
Breaking capacity Icu/Icsno
-
Supply voltage20.4 V DC ... 26.4 V DC
-
Enclosure ratingIP20 (IEC 60529)
Specifications
| Electrical |
| Rated insulation voltage Ui |
690 V (IEC 60947-4-1) |
| Rated impulse withstand Uimp |
6 kV (IEC 60947-4-1) |
| Breaking capacity Icu/Ics |
no |
| Tripping characteristic |
7 mm |
| Supply voltage |
20.4 V DC ... 26.4 V DC |
| Input voltage range |
20.4 V ... 26.4 V |
| Power consumption |
typ. 2 W |
| Frequency |
0.1 Hz |
| Rated torque |
0.5 Nm ... 0.6 Nm |
| I/O and communication |
| Safety integrity SIL/PL |
3 |
| Mechanical |
| Weight |
172.2 g |
| Mounting |
35 mm DIN rail (IEC 60715) |
| Terminal wire size |
150 Ω |
| Enclosure rating |
IP20 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
-25...+60 °C (IEC 60068-2-1) |
| Certifications |
CE, UL, cULus |
| Humidity |
75 % (on average, 85% infrequently, non-condensing) |
| Degree of protection |
IP54 |
Values follow the Phoenix Contact Safety Relay specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Safety Relay variants |
| Catalog number |
Tripping characteristic |
|
2700540 (this page) |
7 mm |
| 2700524 |
7 mm |
| 2700525 |
8 mm |
| 2700569 |
7 mm |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The 2700540 is the device-level element in a Phoenix Contact circuit breaker installation. It receives the field signals and control supply listed above — 20.4 V DC ... 26.4 V DC — and switches or conditions the load within the the rated ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in distribution boards, motor protection circuits, panel feeders, where the unit is matched to the original catalog number and the enclosure provides 35 mm DIN rail (IEC 60715) support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 2700540
Phoenix Contact 2700540 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 2700540; always cross-check the catalog number and hardware revision on the nameplate before placing an order.
- Rated insulation voltage Ui: 690 V (IEC 60947-4-1) — Use it as the reference when cross-checking a current-production equivalent.
- Power consumption: typ. 2 W — Verify it in the project documentation before confirming the order.
- Tripping characteristic: 7 mm — Check this value against the nameplate of the installed unit before ordering.
- Enclosure rating: IP20 (IEC 60529) — Match it to the existing panel and upstream protection.
Datasheets and compliance documents are available on request; quote the full catalog number when enquiring.
Common questions about 2700540
Q.Before ordering 2700540, which rated torque entry should be checked?
The rated torque entry quoted above is 0.5 Nm ... 0.6 Nm. Compare it with the nameplate of the installed unit before ordering.
Q.Where can I find the safety integrity SIL/PL data for 2700540?
It is listed in the specification table for Phoenix Contact 2700540 as 3. Confirm this figure against the unit currently in the panel.
Q.For 2700540, what does the specification table state about frequency?
The specification table lists frequency = 0.1 Hz for Phoenix Contact 2700540. Use the value as the reference when sourcing a current-production equivalent.
Q.What should I include in an enquiry for 2700540?
Send the full catalog number 2700540, the required quantity and a photo of the nameplate. Stock, lead time and the applicable compliance documents can then be confirmed for Phoenix Contact 2700540.
Q.Can the 2700540 replace the unit currently installed in my panel?
Compare catalog number 2700540 and the ratings above with the nameplate of the installed device. A current-production equivalent is selected by function and electrical rating, not by the label alone.