Phoenix Contact · Connector
1772418 is a Phoenix Contact circuit breaker with Rated current Ie 10 A; Tripping characteristic 8 mm; Rated operational voltage <= 440 V AC. It is used in distribution boards, motor protection circuits, panel feeders where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Rated current Ie10 A
-
Tripping characteristic8 mm
-
Rated operational voltage<= 440 V AC
-
Enclosure ratingIP20 (IEC 60529)
Specifications
| Electrical |
| Rated current Ie |
10 A |
| Rated operational voltage |
<= 440 V AC |
| Tripping characteristic |
8 mm |
| Mechanical |
| Weight |
42.4 g |
| Mounting |
DIN rail / panel |
| Terminal wire size |
0.14 mm² ... 2.5 mm² |
| Enclosure rating |
IP20 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
-25...+60 °C |
| Certifications |
CE, UL, cULus |
Values follow the Phoenix Contact Connector specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Connector variants |
| Catalog number |
Tripping characteristic |
Breaking capacity Icu/Ics |
Rated operational voltage |
|
1772418 (this page) |
8 mm |
— |
<= 440 V AC |
| 1773404 |
7 mm (N/O contacts) |
— |
<= 440 V AC |
| 1402398 |
— |
CAT5 (IEC 11801:2002) |
<= 440 V AC |
| 1404549 |
— |
CAT6A |
72 V (DC) |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The 1772418 is the device-level element in a Phoenix Contact circuit breaker installation. It receives the field signals and control supply listed above — <= 440 V AC — and switches or conditions the load within the 10 A ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in distribution boards, motor protection circuits, panel feeders, where the unit is matched to the original catalog number and the enclosure provides DIN rail / panel support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 1772418
Phoenix Contact 1772418 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 1772418; size the surrounding wiring and upstream protection to these published ratings rather than to a generic assumption.
- Weight: 42.4 g — Use it as the reference when cross-checking a current-production equivalent.
- Rated operational voltage: <= 440 V AC — Verify it in the project documentation before confirming the order.
- Tripping characteristic: 8 mm — Check this value against the nameplate of the installed unit before ordering.
- Mounting: DIN rail / panel — Match it to the existing panel and upstream protection.
Available from stock with datasheet, certificates and a quotation on request.
Common questions about 1772418
Q.Which value is published under certifications for catalog number 1772418?
For 1772418, certifications is given as CE, UL, cULus. Compare it with the nameplate of the installed unit before ordering.
Q.Before ordering 1772418, which operating temperature entry should be checked?
The operating temperature entry quoted above is -25...+60 °C. Confirm this figure against the unit currently in the panel.
Q.Where can I find the mounting data for 1772418?
It is listed in the specification table for Phoenix Contact 1772418 as DIN rail / panel. Use the value as the reference when sourcing a current-production equivalent.
Q.How do I confirm compatibility of 1772418 before ordering?
Match the catalog number 1772418 and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.
Q.What should I include in an enquiry for 1772418?
Send the full catalog number 1772418, the required quantity and a photo of the nameplate. Stock, lead time and the applicable compliance documents can then be confirmed for Phoenix Contact 1772418.