Phoenix Contact · Terminal Block
1723014 is a Phoenix Contact circuit breaker with Rated current Ie up to 41 A (IEC 60947-7-1); Tripping characteristic 7 mm; Rated operational voltage 800 V (IEC 60947-7-1). It is used in distribution boards, motor protection circuits, panel feeders where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Rated current Ieup to 41 A (IEC 60947-7-1)
-
Tripping characteristic7 mm
-
Rated operational voltage800 V (IEC 60947-7-1)
-
Breaking capacity Icu/IcsTin-plated
Specifications
| Electrical |
| Rated current Ie |
up to 41 A (IEC 60947-7-1) |
| Rated operational voltage |
800 V (IEC 60947-7-1) |
| Rated insulation voltage Ui |
250 V |
| Breaking capacity Icu/Ics |
Tin-plated |
| Tripping characteristic |
7 mm |
| Frequency |
10 - 150 - 10 Hz |
| Rated torque |
0.5 Nm ... 0.6 Nm |
| Rated speed |
1 octave/min |
| Mechanical |
| Dimensions (H x W x D) |
0.9 x 0.9 mm |
| Weight |
16.666 g |
| Mounting |
35 mm DIN rail (IEC 60715) |
| Terminal type |
Tin (4 µm - 8 µm Sn) |
| Terminal wire size |
0.2 mm² ... 4 mm² |
| Environment and compliance |
| Operating temperature |
-40 °C ... 70 °C |
| Certifications |
CE, UL, cULus |
| Humidity |
30 % ... 70 % |
Values follow the Phoenix Contact Terminal Block specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Terminal Block variants |
| Catalog number |
Tripping characteristic |
Breaking capacity Icu/Ics |
Rated operational voltage |
|
1723014 (this page) |
7 mm |
Tin-plated |
800 V (IEC 60947-7-1) |
| 1720017 |
8 mm |
Tin-plated |
800 V (IEC 60947-7-1) |
| 1720020 |
8 mm |
Tin-plated |
800 V (IEC 60947-7-1) |
| 1725041 |
7 mm |
Tin-plated |
800 V (IEC 60947-7-1) |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The 1723014 is the device-level element in a Phoenix Contact circuit breaker installation. It receives the field signals and control supply listed above — 800 V (IEC 60947-7-1) — and switches or conditions the load within the up to 41 A (IEC 60947-7-1) ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in distribution boards, motor protection circuits, panel feeders, where the unit is matched to the original catalog number and the enclosure provides 35 mm DIN rail (IEC 60715) support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 1723014
Phoenix Contact 1723014 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 1723014; size the surrounding wiring and upstream protection to these published ratings rather than to a generic assumption.
- Breaking capacity Icu/Ics: Tin-plated — Use it as the reference when cross-checking a current-production equivalent.
- Humidity: 30 % ... 70 % — Verify it in the project documentation before confirming the order.
- Mounting: 35 mm DIN rail (IEC 60715) — Check this value against the nameplate of the installed unit before ordering.
- Dimensions (H x W x D): 0.9 x 0.9 mm — Match it to the existing panel and upstream protection.
Available from stock with datasheet, certificates and a quotation on request.
Common questions about 1723014
Q.Which value is published under frequency for catalog number 1723014?
For 1723014, frequency is given as 10 - 150 - 10 Hz. Confirm this figure against the unit currently in the panel.
Q.Before ordering 1723014, which weight entry should be checked?
The weight entry quoted above is 16.666 g. Use the value as the reference when sourcing a current-production equivalent.
Q.Where can I find the terminal wire size data for 1723014?
It is listed in the specification table for Phoenix Contact 1723014 as 0.2 mm² ... 4 mm². Check the revision of the installed unit if the catalog number has been superseded.
Q.How do I confirm compatibility of 1723014 before ordering?
Match the catalog number 1723014 and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.
Q.What should I include in an enquiry for 1723014?
Send the full catalog number 1723014, the required quantity and a photo of the nameplate. Stock, lead time and the applicable compliance documents can then be confirmed for Phoenix Contact 1723014.