Phoenix Contact · Power Distributor
1452851 is a Phoenix Contact circuit breaker with Rated current Ie 10 A; Tripping characteristic 7 mm; Breaking capacity Icu/Ics Supply voltage Green LED. It is used in distribution boards, motor protection circuits, panel feeders where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Rated current Ie10 A
-
Tripping characteristic7 mm
-
Breaking capacity Icu/IcsSupply voltage Green LED
-
Enclosure ratingIP20 (IEC 60529)
Specifications
| Electrical |
| Rated current Ie |
10 A |
| Breaking capacity Icu/Ics |
Supply voltage Green LED |
| Tripping characteristic |
7 mm |
| Input voltage range |
85...264 V AC / 110...300 V DC (IEC 61010) |
| Efficiency |
up to 94 % |
| Rated torque |
1 Nm |
| Mechanical |
| Weight |
232 g |
| Mounting |
35 mm DIN rail (IEC 60715) |
| Terminal wire size |
0.14 mm² ... 1.5 mm² |
| Enclosure rating |
IP20 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
-25...+70 °C (IEC 60068-2-1) |
| Certifications |
CE, UL, cULus |
Values follow the Phoenix Contact Power Distributor specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Power Distributor variants |
| Catalog number |
Breaking capacity Icu/Ics |
|
1452851 (this page) |
Supply voltage Green LED |
| 1452437 |
— |
| 1452699 |
Supply voltage Green LED |
| 1452709 |
Supply voltage Green LED |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The 1452851 is the device-level element in a Phoenix Contact circuit breaker installation. It receives the field signals and control supply listed above — the rated supply — and switches or conditions the load within the 10 A ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in distribution boards, motor protection circuits, panel feeders, where the unit is matched to the original catalog number and the enclosure provides 35 mm DIN rail (IEC 60715) support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 1452851
Phoenix Contact 1452851 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 1452851; always cross-check the catalog number and hardware revision on the nameplate before placing an order.
- Input voltage range: 85...264 V AC / 110...300 V DC (IEC 61010) — Use it as the reference when cross-checking a current-production equivalent.
- Mounting: 35 mm DIN rail (IEC 60715) — Verify it in the project documentation before confirming the order.
- Tripping characteristic: 7 mm — Check this value against the nameplate of the installed unit before ordering.
- Terminal wire size: 0.14 mm² ... 1.5 mm² — Match it to the existing panel and upstream protection.
For a discontinued unit, match function and electrical ratings rather than the label alone.
Common questions about 1452851
Q.Before ordering 1452851, which rated current Ie entry should be checked?
The rated current Ie entry quoted above is 10 A. Compare it with the nameplate of the installed unit before ordering.
Q.Where can I find the efficiency data for 1452851?
It is listed in the specification table for Phoenix Contact 1452851 as up to 94 %. Confirm this figure against the unit currently in the panel.
Q.For 1452851, what does the specification table state about input voltage range?
The specification table lists input voltage range = 85...264 V AC / 110...300 V DC (IEC 61010) for Phoenix Contact 1452851. Use the value as the reference when sourcing a current-production equivalent.
Q.What should I include in an enquiry for 1452851?
Send the full catalog number 1452851, the required quantity and a photo of the nameplate. Stock, lead time and the applicable compliance documents can then be confirmed for Phoenix Contact 1452851.
Q.How do I confirm compatibility of 1452851 before ordering?
Match the catalog number 1452851 and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.