Phoenix Contact · Network Switch
1085173 is a Phoenix Contact circuit breaker with Tripping characteristic 10 mm; Breaking capacity Icu/Ics Ethernet in RJ45 twisted pair; Supply voltage 24 V DC (IEC 61131-2). It is used in distribution boards, motor protection circuits, panel feeders where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Tripping characteristic10 mm
-
Breaking capacity Icu/IcsEthernet in RJ45 twisted pair
-
Supply voltage24 V DC (IEC 61131-2)
-
Enclosure ratingIP20 (IEC 60529)
Specifications
| Electrical |
| Breaking capacity Icu/Ics |
Ethernet in RJ45 twisted pair |
| Tripping characteristic |
10 mm |
| Supply voltage |
24 V DC (IEC 61131-2) |
| Rated speed |
10/100/1000 Mbps |
| Mechanical |
| Weight |
218 g |
| Mounting |
35 mm DIN rail (IEC 60715) |
| Terminal wire size |
0.2 mm² ... 2.5 mm² |
| Enclosure rating |
IP20 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
0...+55 °C (IEC 60068-2-1) |
| Certifications |
CE, UL, cULus |
| Humidity |
5 % ... 95 % (non-condensing) |
Values follow the Phoenix Contact Network Switch specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Network Switch variants |
| Catalog number |
Tripping characteristic |
Breaking capacity Icu/Ics |
|
1085173 (this page) |
10 mm |
Ethernet in RJ45 twisted pair |
| 1085176 |
10 mm |
Ethernet in RJ45 twisted pair |
| 1085039 |
10 mm |
Ethernet in RJ45 twisted pair |
| 1085219 |
10 mm |
Ethernet in RJ45 twisted pair |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The 1085173 is the device-level element in a Phoenix Contact circuit breaker installation. It receives the field signals and control supply listed above — 24 V DC (IEC 61131-2) — and switches or conditions the load within the the rated ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in distribution boards, motor protection circuits, panel feeders, where the unit is matched to the original catalog number and the enclosure provides 35 mm DIN rail (IEC 60715) support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 1085173
Phoenix Contact 1085173 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 1085173; record the nameplate data of the unit being replaced before selecting an equivalent.
- Rated speed: 10/100/1000 Mbps — Use it as the reference when cross-checking a current-production equivalent.
- Tripping characteristic: 10 mm — Verify it in the project documentation before confirming the order.
- Weight: 218 g — Check this value against the nameplate of the installed unit before ordering.
- Supply voltage: 24 V DC (IEC 61131-2) — Match it to the existing panel and upstream protection.
Cross-check the ratings above with the installed device before confirming the order.
Common questions about 1085173
Q.Which value is published under rated speed for catalog number 1085173?
For 1085173, rated speed is given as 10/100/1000 Mbps. Check the revision of the installed unit if the catalog number has been superseded.
Q.Before ordering 1085173, which enclosure rating entry should be checked?
The enclosure rating entry quoted above is IP20 (IEC 60529). Compare it with the nameplate of the installed unit before ordering.
Q.Where can I find the weight data for 1085173?
It is listed in the specification table for Phoenix Contact 1085173 as 218 g. Confirm this figure against the unit currently in the panel.
Q.What should I include in an enquiry for 1085173?
Send the full catalog number 1085173, the required quantity and a photo of the nameplate. Stock, lead time and the applicable compliance documents can then be confirmed for Phoenix Contact 1085173.
Q.Can the 1085173 replace the unit currently installed in my panel?
Compare catalog number 1085173 and the ratings above with the nameplate of the installed device. A current-production equivalent is selected by function and electrical rating, not by the label alone.