Phoenix Contact · Network Switch
1026937 is a Phoenix Contact circuit breaker with Tripping characteristic 7 mm; Breaking capacity Icu/Ics Ethernet RJ45; Supply voltage 24 V DC (IEC 61131-2). It is used in distribution boards, motor protection circuits, panel feeders where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Tripping characteristic7 mm
-
Breaking capacity Icu/IcsEthernet RJ45
-
Supply voltage24 V DC (IEC 61131-2)
-
Enclosure ratingIP20 (IEC 60529)
Specifications
| Electrical |
| Breaking capacity Icu/Ics |
Ethernet RJ45 |
| Tripping characteristic |
7 mm |
| Coil voltage |
48 V DC |
| Supply voltage |
24 V DC (IEC 61131-2) |
| Rated speed |
10/100/1000 Mbps (full duplex) |
| Mechanical |
| Weight |
623.1 g |
| Mounting |
35 mm DIN rail (IEC 60715) |
| Terminal wire size |
0.2 mm² ... 2.5 mm² |
| Enclosure rating |
IP20 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
0...+55 °C (IEC 60068-2-1) |
| Certifications |
CE, UL, cULus |
| Humidity |
5 % ... 95 % (non-condensing) |
Values follow the Phoenix Contact Network Switch specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Network Switch variants |
| Catalog number |
Breaking capacity Icu/Ics |
Tripping characteristic |
|
1026937 (this page) |
Ethernet RJ45 |
7 mm |
| 1026932 |
Ethernet RJ45 |
7 mm |
| 1026922 |
Ethernet in RJ45 twisted pair |
7 mm |
| 1026929 |
Ethernet RJ45 |
7 mm |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The 1026937 is the device-level element in a Phoenix Contact circuit breaker installation. It receives the field signals and control supply listed above — 24 V DC (IEC 61131-2) — and switches or conditions the load within the the rated ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in distribution boards, motor protection circuits, panel feeders, where the unit is matched to the original catalog number and the enclosure provides 35 mm DIN rail (IEC 60715) support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 1026937
Phoenix Contact 1026937 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 1026937; always cross-check the catalog number and hardware revision on the nameplate before placing an order.
- Terminal wire size: 0.2 mm² ... 2.5 mm² — Check this value against the nameplate of the installed unit before ordering.
- Humidity: 5 % ... 95 % (non-condensing) — Match it to the existing panel and upstream protection.
- Certifications: CE, UL, cULus — Record it with the other nameplate data when sourcing a replacement.
- Enclosure rating: IP20 (IEC 60529) — Confirm the revision of the installed unit before a like-for-like replacement.
For a discontinued unit, match function and electrical ratings rather than the label alone.
Common questions about 1026937
Q.Which value is published under tripping characteristic for catalog number 1026937?
For 1026937, tripping characteristic is given as 7 mm. Compare it with the nameplate of the installed unit before ordering.
Q.Before ordering 1026937, which coil voltage entry should be checked?
The coil voltage entry quoted above is 48 V DC. Confirm this figure against the unit currently in the panel.
Q.Where can I find the rated speed data for 1026937?
It is listed in the specification table for Phoenix Contact 1026937 as 10/100/1000 Mbps (full duplex). Use the value as the reference when sourcing a current-production equivalent.
Q.What should I include in an enquiry for 1026937?
Send the full catalog number 1026937, the required quantity and a photo of the nameplate. Stock, lead time and the applicable compliance documents can then be confirmed for Phoenix Contact 1026937.
Q.How do I confirm compatibility of 1026937 before ordering?
Match the catalog number 1026937 and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.