IFM · Inductive proximity sensor
IG0307 is an IFM circuit breaker with Breaking capacity Icu/Ics no; Supply voltage 10...30 V DC (IEC 60947-5-2); Enclosure rating IP67 (IEC 60529). It is used in distribution boards, motor protection circuits, panel feeders where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Breaking capacity Icu/Icsno
-
Supply voltage10...30 V DC (IEC 60947-5-2)
-
Enclosure ratingIP67 (IEC 60529)
-
Mountingnon-flush mountable
Specifications
| Electrical |
| Breaking capacity Icu/Ics |
no |
| Supply voltage |
10...30 V DC (IEC 60947-5-2) |
| Frequency |
25 Hz |
| Overload capacity |
no |
| Rated torque |
23 Nm |
| Mechanical |
| Dimensions (H x W x D) |
M18 x 1 / L = 80 mm |
| Weight |
151.6 g |
| Mounting |
non-flush mountable |
| Enclosure rating |
IP67 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
-25...+70 °C (IEC 60068-2-1) |
| Certifications |
CE, cULus |
Values follow the IFM Inductive proximity sensor specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| IFM Inductive proximity sensor variants |
| Catalog number |
Breaking capacity Icu/Ics |
|
IG0307 (this page) |
no |
| IG0305 |
no |
| IG0309 |
— |
| IG0310 |
— |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The IG0307 is the device-level element in an IFM circuit breaker installation. It receives the field signals and control supply listed above — 10...30 V DC (IEC 60947-5-2) — and switches or conditions the load within the the rated ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in distribution boards, motor protection circuits, panel feeders, where the unit is matched to the original catalog number and the enclosure provides non-flush mountable support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for IFM IG0307
IFM IG0307 — Sensor or detector for object detection, distance measurement and status feedback on production lines. The figures below are taken from the specification table on this page for catalog number IG0307; size the surrounding wiring and upstream protection to these published ratings rather than to a generic assumption.
- Certifications: CE, cULus — Match it to the existing panel and upstream protection.
- Weight: 151.6 g — Record it with the other nameplate data when sourcing a replacement.
- Mounting: non-flush mountable — Confirm the revision of the installed unit before a like-for-like replacement.
- Overload capacity: no — Use it as the reference when cross-checking a current-production equivalent.
For a discontinued unit, match function and electrical ratings rather than the label alone.
Common questions about IG0307
Q.Where can I find the enclosure rating data for IG0307?
It is listed in the specification table for IFM IG0307 as IP67 (IEC 60529). Use the value as the reference when sourcing a current-production equivalent.
Q.For IG0307, what does the specification table state about weight?
The specification table lists weight = 151.6 g for IFM IG0307. Check the revision of the installed unit if the catalog number has been superseded.
Q.Which value is published under frequency for catalog number IG0307?
For IG0307, frequency is given as 25 Hz. Compare it with the nameplate of the installed unit before ordering.
Q.How do I confirm compatibility of IG0307 before ordering?
Match the catalog number IG0307 and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.
Q.What should I include in an enquiry for IG0307?
Send the full catalog number IG0307, the required quantity and a photo of the nameplate. Stock, lead time and the applicable compliance documents can then be confirmed for IFM IG0307.