IFM · Inductive proximity sensor
IG0087 is an IFM circuit breaker with Breaking capacity Icu/Ics no; Supply voltage 10...30 V DC (IEC 60947-5-2); Enclosure rating IP67 (IEC 60529). It is used in distribution boards, motor protection circuits, panel feeders where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Breaking capacity Icu/Icsno
-
Supply voltage10...30 V DC (IEC 60947-5-2)
-
Enclosure ratingIP67 (IEC 60529)
-
Mountingnon-flush mountable
Specifications
| Electrical |
| Breaking capacity Icu/Ics |
no |
| Supply voltage |
10...30 V DC (IEC 60947-5-2) |
| Frequency |
25 Hz |
| Overload capacity |
no |
| Mechanical |
| Dimensions (H x W x D) |
M18 x 1 / L = 80 mm |
| Weight |
479 g |
| Mounting |
non-flush mountable |
| Enclosure rating |
IP67 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
-25...+70 °C (IEC 60068-2-1) |
| Certifications |
CE, cULus |
Values follow the IFM Inductive proximity sensor specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| IFM Inductive proximity sensor variants |
| Catalog number |
Breaking capacity Icu/Ics |
|
IG0087 (this page) |
no |
| IG0083 |
no |
| IG0006 |
no |
| IG0011 |
no |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The IG0087 is the device-level element in an IFM circuit breaker installation. It receives the field signals and control supply listed above — 10...30 V DC (IEC 60947-5-2) — and switches or conditions the load within the the rated ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in distribution boards, motor protection circuits, panel feeders, where the unit is matched to the original catalog number and the enclosure provides non-flush mountable support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for IFM IG0087
IFM IG0087 — Sensor or detector for object detection, distance measurement and status feedback on production lines. The figures below are taken from the specification table on this page for catalog number IG0087; size the surrounding wiring and upstream protection to these published ratings rather than to a generic assumption.
- Operating temperature: -25...+70 °C (IEC 60068-2-1) — Use it as the reference when cross-checking a current-production equivalent.
- Dimensions (H x W x D): M18 x 1 / L = 80 mm — Verify it in the project documentation before confirming the order.
- Weight: 479 g — Check this value against the nameplate of the installed unit before ordering.
- Enclosure rating: IP67 (IEC 60529) — Match it to the existing panel and upstream protection.
Available from stock with datasheet, certificates and a quotation on request.
Common questions about IG0087
Q.Where can I find the dimensions (H x W x D) data for IG0087?
It is listed in the specification table for IFM IG0087 as M18 x 1 / L = 80 mm. Check the revision of the installed unit if the catalog number has been superseded.
Q.For IG0087, what does the specification table state about operating temperature?
The specification table lists operating temperature = -25...+70 °C (IEC 60068-2-1) for IFM IG0087. Compare it with the nameplate of the installed unit before ordering.
Q.Which value is published under weight for catalog number IG0087?
For IG0087, weight is given as 479 g. Confirm this figure against the unit currently in the panel.
Q.How do I confirm compatibility of IG0087 before ordering?
Match the catalog number IG0087 and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.
Q.Can the IG0087 replace the unit currently installed in my panel?
Compare catalog number IG0087 and the ratings above with the nameplate of the installed device. A current-production equivalent is selected by function and electrical rating, not by the label alone.