IFM · I/O Module
AL3050 is an IFM I/O module with Supply voltage 24 V DC (IEC 61131-2); Enclosure rating IP20 (IEC 60529); Communication ports Ethernet. It is used in packaging machines, conveyor transfer cells, small process skids where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Supply voltage24 V DC (IEC 61131-2)
-
Enclosure ratingIP20 (IEC 60529)
-
Communication portsEthernet
-
Mounting35 mm DIN rail (IEC 60715)
Specifications
| Electrical |
| Supply voltage |
24 V DC (IEC 61131-2) |
| I/O and communication |
| Communication ports |
Ethernet |
| Response time |
< 1 ms |
| Mechanical |
| Weight |
296.6 g |
| Mounting |
35 mm DIN rail (IEC 60715) |
| Enclosure rating |
IP20 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
0...+55 °C (IEC 60068-2-1) |
| Storage temperature |
-25...85 °C |
| Certifications |
CE, cULus |
Values follow the IFM I/O Module specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| IFM I/O Module variants |
| Catalog number |
Supply voltage |
|
AL3050 (this page) |
24 V DC (IEC 61131-2) |
| AL3150 |
24 V DC (IEC 61131-2) |
| AL1010 |
24 V DC (IEC 61131-2) |
| AL1020 |
24 V DC (IEC 61131-2) |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The AL3050 is the device-level element in an IFM I/O module installation. It receives the field signals and control supply listed above — 24 V DC (IEC 61131-2) — and switches or conditions the load within the the rated ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in packaging machines, conveyor transfer cells, small process skids, where the unit is matched to the original catalog number and the enclosure provides 35 mm DIN rail (IEC 60715) support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for IFM AL3050
IFM AL3050 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number AL3050; verify the catalog number against your bill of materials before requesting a quotation.
- Mounting: 35 mm DIN rail (IEC 60715) — Check this value against the nameplate of the installed unit before ordering.
- Enclosure rating: IP20 (IEC 60529) — Match it to the existing panel and upstream protection.
- Response time: < 1 ms — Record it with the other nameplate data when sourcing a replacement.
- Supply voltage: 24 V DC (IEC 61131-2) — Confirm the revision of the installed unit before a like-for-like replacement.
Available from stock with datasheet, certificates and a quotation on request.
Common questions about AL3050
Q.Which value is published under supply voltage for catalog number AL3050?
For AL3050, supply voltage is given as 24 V DC (IEC 61131-2). Use the value as the reference when sourcing a current-production equivalent.
Q.Before ordering AL3050, which weight entry should be checked?
The weight entry quoted above is 296.6 g. Check the revision of the installed unit if the catalog number has been superseded.
Q.Where can I find the mounting data for AL3050?
It is listed in the specification table for IFM AL3050 as 35 mm DIN rail (IEC 60715). Compare it with the nameplate of the installed unit before ordering.
Q.How do I confirm compatibility of AL3050 before ordering?
Match the catalog number AL3050 and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.
Q.Can the AL3050 replace the unit currently installed in my panel?
Compare catalog number AL3050 and the ratings above with the nameplate of the installed device. A current-production equivalent is selected by function and electrical rating, not by the label alone.