Phoenix Contact · Temperature Transmitter
2865654 is a Phoenix Contact power supply with Output voltage 6 V DC; Output current 7 mA (RTD in 2-conductor technology); Supply voltage 11...30 V DC (loop powered). It is used in DIN-rail control cabinets, sensor and relay supplies, backplane bus power where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Output voltage6 V DC
-
Output current7 mA (RTD in 2-conductor technology)
-
Supply voltage11...30 V DC (loop powered)
-
Enclosure ratingIP66 / IP67 (IEC 60529)
Specifications
| Electrical |
| Rated insulation voltage Ui |
375 V P |
| Tripping characteristic |
7 mm |
| Supply voltage |
11...30 V DC (loop powered) |
| Output voltage |
6 V DC |
| Output current |
7 mA (RTD in 2-conductor technology) |
| Rated torque |
0.5 Nm ... 0.6 Nm |
| I/O and communication |
| Response time |
≤ 1.75 s (SIL on) |
| Mechanical |
| Weight |
272.6 g |
| Mounting |
DIN rail mounting |
| Terminal wire size |
0.2 mm² ... 2.5 mm² |
| Enclosure rating |
IP66 / IP67 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
-40...+85 °C (IEC 60068-2-1) |
| Certifications |
CE, UL, cULus |
| Humidity |
typ. 5 % ... 95 % (non-condensing) |
Values follow the Phoenix Contact Temperature Transmitter specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Temperature Transmitter variants |
| Catalog number |
Mounting |
|
2865654 (this page) |
DIN rail mounting |
| 2865696 |
DIN rail / panel |
| 2865007 |
DIN rail mounting |
| 2865010 |
DIN rail mounting |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The 2865654 is the device-level element in a Phoenix Contact power supply installation. It receives the field signals and control supply listed above — 11...30 V DC (loop powered) — and switches or conditions the load within the the rated ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in DIN-rail control cabinets, sensor and relay supplies, backplane bus power, where the unit is matched to the original catalog number and the enclosure provides DIN rail mounting support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 2865654
Phoenix Contact 2865654 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 2865654; always cross-check the catalog number and hardware revision on the nameplate before placing an order.
- Mounting: DIN rail mounting — Check this value against the nameplate of the installed unit before ordering.
- Rated insulation voltage Ui: 375 V P — Match it to the existing panel and upstream protection.
- Operating temperature: -40...+85 °C (IEC 60068-2-1) — Record it with the other nameplate data when sourcing a replacement.
- Tripping characteristic: 7 mm — Confirm the revision of the installed unit before a like-for-like replacement.
For a discontinued unit, match function and electrical ratings rather than the label alone.
Common questions about 2865654
Q.Where can I find the mounting data for 2865654?
It is listed in the specification table for Phoenix Contact 2865654 as DIN rail mounting. Use the value as the reference when sourcing a current-production equivalent.
Q.For 2865654, what does the specification table state about supply voltage?
The specification table lists supply voltage = 11...30 V DC (loop powered) for Phoenix Contact 2865654. Check the revision of the installed unit if the catalog number has been superseded.
Q.Which value is published under rated torque for catalog number 2865654?
For 2865654, rated torque is given as 0.5 Nm ... 0.6 Nm. Compare it with the nameplate of the installed unit before ordering.
Q.What should I include in an enquiry for 2865654?
Send the full catalog number 2865654, the required quantity and a photo of the nameplate. Stock, lead time and the applicable compliance documents can then be confirmed for Phoenix Contact 2865654.
Q.Can the 2865654 replace the unit currently installed in my panel?
Compare catalog number 2865654 and the ratings above with the nameplate of the installed device. A current-production equivalent is selected by function and electrical rating, not by the label alone.