Phoenix Contact · Temperature Transmitter
2865010 is a Phoenix Contact circuit breaker with Tripping characteristic 7 mm; Breaking capacity Icu/Ics 8 mA; Supply voltage 11...30 V DC (loop powered). It is used in distribution boards, motor protection circuits, panel feeders where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Tripping characteristic7 mm
-
Breaking capacity Icu/Ics8 mA
-
Supply voltage11...30 V DC (loop powered)
-
Enclosure ratingIP66 / IP67 (IEC 60529)
Specifications
| Electrical |
| Rated insulation voltage Ui |
300 V rms |
| Breaking capacity Icu/Ics |
8 mA |
| Tripping characteristic |
7 mm |
| Supply voltage |
11...30 V DC (loop powered) |
| Frequency |
≤ 20 Hz (without load) |
| Rated torque |
0.5 Nm ... 0.6 Nm |
| I/O and communication |
| Safety integrity SIL/PL |
2 |
| Mechanical |
| Weight |
181 g |
| Mounting |
DIN rail mounting |
| Terminal wire size |
0.2 mm² ... 2.5 mm² |
| Enclosure rating |
IP66 / IP67 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
-40...+85 °C (IEC 60068-2-1) |
| Certifications |
CE, UL, cULus |
| Humidity |
10 % ... 95 % (non-condensing) |
Values follow the Phoenix Contact Temperature Transmitter specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Temperature Transmitter variants |
| Catalog number |
Tripping characteristic |
Breaking capacity Icu/Ics |
|
2865010 (this page) |
7 mm |
8 mA |
| 2865007 |
12 mm |
≤ 22 mA |
| 2865049 |
7 mm |
8 mA |
| 2865405 |
7 mm |
— |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The 2865010 is the device-level element in a Phoenix Contact circuit breaker installation. It receives the field signals and control supply listed above — 11...30 V DC (loop powered) — and switches or conditions the load within the the rated ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in distribution boards, motor protection circuits, panel feeders, where the unit is matched to the original catalog number and the enclosure provides DIN rail mounting support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 2865010
Phoenix Contact 2865010 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 2865010; record the nameplate data of the unit being replaced before selecting an equivalent.
- Rated torque: 0.5 Nm ... 0.6 Nm — Record it with the other nameplate data when sourcing a replacement.
- Supply voltage: 11...30 V DC (loop powered) — Confirm the revision of the installed unit before a like-for-like replacement.
- Rated insulation voltage Ui: 300 V rms — Use it as the reference when cross-checking a current-production equivalent.
- Frequency: ≤ 20 Hz (without load) — Verify it in the project documentation before confirming the order.
Cross-check the ratings above with the installed device before confirming the order.
Common questions about 2865010
Q.Which value is published under tripping characteristic for catalog number 2865010?
For 2865010, tripping characteristic is given as 7 mm. Confirm this figure against the unit currently in the panel.
Q.Before ordering 2865010, which mounting entry should be checked?
The mounting entry quoted above is DIN rail mounting. Use the value as the reference when sourcing a current-production equivalent.
Q.Where can I find the operating temperature data for 2865010?
It is listed in the specification table for Phoenix Contact 2865010 as -40...+85 °C (IEC 60068-2-1). Check the revision of the installed unit if the catalog number has been superseded.
Q.What should I include in an enquiry for 2865010?
Send the full catalog number 2865010, the required quantity and a photo of the nameplate. Stock, lead time and the applicable compliance documents can then be confirmed for Phoenix Contact 2865010.
Q.Can the 2865010 replace the unit currently installed in my panel?
Compare catalog number 2865010 and the ratings above with the nameplate of the installed device. A current-production equivalent is selected by function and electrical rating, not by the label alone.