Schneider Electric · ComPacT circuit breaker
LV426113 is a Schneider Electric circuit breaker with Rated current Ie 40 A; Rated operational voltage up to 690 V AC; Breaking capacity Icu/Ics 100% Icu. It is used in distribution boards, motor protection circuits, panel feeders where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Rated current Ie40 A
-
Rated operational voltageup to 690 V AC
-
Breaking capacity Icu/Ics100% Icu
-
Enclosure ratingIP40 conforming to IEC 60529
Specifications
| Electrical |
| Rated current Ie |
40 A |
| Rated operational voltage |
up to 690 V AC |
| Rated insulation voltage Ui |
750 V AC conforming to IEC 60947-2 |
| Rated impulse withstand Uimp |
8 kV conforming to IEC 60947-2 |
| Breaking capacity Icu/Ics |
100% Icu |
| Mechanical |
| Weight |
1.42 kg |
| Mounting |
By screws (plate) |
| Enclosure rating |
IP40 conforming to IEC 60529 |
| Environment and compliance |
| Operating temperature |
-25...+70 °C |
| Certifications |
CCC, CE, EAC, marine approvals |
| Degree of protection |
IP40 |
Values follow the Schneider Electric ComPacT circuit breaker specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Schneider Electric ComPacT circuit breaker variants |
| Catalog number |
Breaking capacity Icu/Ics |
Rated operational voltage |
|
LV426113 (this page) |
100% Icu |
up to 690 V AC |
| LV426118 |
100% Icu |
up to 690 V AC |
| LV426119 |
100% Icu |
up to 690 V AC |
| LV426101 |
100% Icu |
up to 690 V AC |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The LV426113 is the device-level element in a Schneider Electric circuit breaker installation. It receives the field signals and control supply listed above — up to 690 V AC — and switches or conditions the load within the 40 A ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in distribution boards, motor protection circuits, panel feeders, where the unit is matched to the original catalog number and the enclosure provides By screws (plate) support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Schneider Electric LV426113
Schneider Electric LV426113 — Circuit breaker providing branch-circuit overload and short-circuit protection in distribution boards and panel feeders. The figures below are taken from the specification table on this page for catalog number LV426113; size the surrounding wiring and upstream protection to these published ratings rather than to a generic assumption.
- Rated current Ie: 40 A — Confirm the revision of the installed unit before a like-for-like replacement.
- Rated impulse withstand Uimp: 8 kV conforming to IEC 60947-2 — Use it as the reference when cross-checking a current-production equivalent.
- Rated operational voltage: up to 690 V AC — Verify it in the project documentation before confirming the order.
- Weight: 1.42 kg — Check this value against the nameplate of the installed unit before ordering.
Available from stock with datasheet, certificates and a quotation on request.
Common questions about LV426113
Q.Which value is published under certifications for catalog number LV426113?
For LV426113, certifications is given as CCC, CE, EAC, marine approvals. Check the revision of the installed unit if the catalog number has been superseded.
Q.Before ordering LV426113, which weight entry should be checked?
The weight entry quoted above is 1.42 kg. Compare it with the nameplate of the installed unit before ordering.
Q.Where can I find the mounting data for LV426113?
It is listed in the specification table for Schneider Electric LV426113 as By screws (plate). Confirm this figure against the unit currently in the panel.
Q.What should I include in an enquiry for LV426113?
Send the full catalog number LV426113, the required quantity and a photo of the nameplate. Stock, lead time and the applicable compliance documents can then be confirmed for Schneider Electric LV426113.
Q.Can the LV426113 replace the unit currently installed in my panel?
Compare catalog number LV426113 and the ratings above with the nameplate of the installed device. A current-production equivalent is selected by function and electrical rating, not by the label alone.