Phoenix Contact · Wireless module / WLAN access point
1043201 is a Phoenix Contact circuit breaker with Breaking capacity Icu/Ics Copper; Enclosure rating IP20 (IEC 60529); Mounting DIN rail / panel. It is used in distribution boards, motor protection circuits, panel feeders where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Breaking capacity Icu/IcsCopper
-
Enclosure ratingIP20 (IEC 60529)
-
MountingDIN rail / panel
-
Operating temperature0...+55 °C (IEC 60068-2-1)
Specifications
| Electrical |
| Breaking capacity Icu/Ics |
Copper |
| Frequency |
2.4 GHz |
| Rated speed |
10/100 Mbps |
| Mechanical |
| Dimensions (H x W x D) |
Height with antenna socket, without antenna cable |
| Weight |
540.3 g |
| Mounting |
DIN rail / panel |
| Enclosure rating |
IP20 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
0...+55 °C (IEC 60068-2-1) |
| Certifications |
CE, UL, cULus |
| Humidity |
10 % ... 95 % (non-condensing) |
Values follow the Phoenix Contact Wireless module / WLAN access point specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Where it sits in the control system
The 1043201 is the device-level element in a Phoenix Contact circuit breaker installation. It receives the field signals and control supply listed above — the rated supply — and switches or conditions the load within the the rated ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in distribution boards, motor protection circuits, panel feeders, where the unit is matched to the original catalog number and the enclosure provides DIN rail / panel support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 1043201
Phoenix Contact 1043201 — Sensor or detector for object detection, distance measurement and status feedback on production lines. The figures below are taken from the specification table on this page for catalog number 1043201; confirm the installed unit's part number and revision so the replacement matches both electrically and mechanically.
- Mounting: DIN rail / panel — Check this value against the nameplate of the installed unit before ordering.
- Operating temperature: 0...+55 °C (IEC 60068-2-1) — Match it to the existing panel and upstream protection.
- Breaking capacity Icu/Ics: Copper — Record it with the other nameplate data when sourcing a replacement.
- Frequency: 2.4 GHz — Confirm the revision of the installed unit before a like-for-like replacement.
Cross-check the ratings above with the installed device before confirming the order.
Common questions about 1043201
Q.Where can I find the mounting data for 1043201?
It is listed in the specification table for Phoenix Contact 1043201 as DIN rail / panel. Use the value as the reference when sourcing a current-production equivalent.
Q.For 1043201, what does the specification table state about operating temperature?
The specification table lists operating temperature = 0...+55 °C (IEC 60068-2-1) for Phoenix Contact 1043201. Check the revision of the installed unit if the catalog number has been superseded.
Q.Which value is published under certifications for catalog number 1043201?
For 1043201, certifications is given as CE, UL, cULus. Compare it with the nameplate of the installed unit before ordering.
Q.How do I confirm compatibility of 1043201 before ordering?
Match the catalog number 1043201 and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.
Q.What should I include in an enquiry for 1043201?
Send the full catalog number 1043201, the required quantity and a photo of the nameplate. Stock, lead time and the applicable compliance documents can then be confirmed for Phoenix Contact 1043201.