Omron · Fiber-optic sensor / amplifier
E3NX-CA0 is an Omron color fiber amplifier with Rated current Ie up to 4 A; Supply voltage 24 VDC (20.4 to 26.4 V); Enclosure rating IP67 (IEC 60529). It is used in control panels, machine builds, spare-part replacements where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Rated current Ieup to 4 A
-
Supply voltage24 VDC (20.4 to 26.4 V)
-
Enclosure ratingIP67 (IEC 60529)
-
Operating temperature-25...+80 °C (IEC 60068-2-1)
Specifications
| Electrical |
| Rated current Ie |
up to 4 A |
| Supply voltage |
24 VDC (20.4 to 26.4 V) |
| Mechanical |
| Weight |
Approx. 185 g/approx. 95 g |
| Mounting |
35-mm DIN track - mounting |
| Enclosure rating |
IP67 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
-25...+80 °C (IEC 60068-2-1) |
| Certifications |
CE, UL, cULus |
Values follow the Omron Fiber-optic sensor / amplifier specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Omron Fiber-optic sensor / amplifier variants |
| Catalog number |
Mounting |
Rated current Ie |
|
E3NX-CA0 (this page) |
35-mm DIN track - mounting |
up to 4 A |
| E3NXCA112M |
DIN rail / panel |
up to 4 A |
| E3NXCA512M |
DIN rail / panel |
up to 4 A |
| E3NXFA0 |
DIN rail / panel |
up to 4 A |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The E3NX-CA0 is the device-level element in an Omron color fiber amplifier installation. It receives the field signals and control supply listed above — 24 VDC (20.4 to 26.4 V) — and switches or conditions the load within the up to 4 A ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in control panels, machine builds, spare-part replacements, where the unit is matched to the original catalog number and the enclosure provides 35-mm DIN track - mounting support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Omron E3NX-CA0
Omron E3NX-CA0 — Sensor or detector for object detection, distance measurement and status feedback on production lines. The figures below are taken from the specification table on this page for catalog number E3NX-CA0; confirm the installed unit's part number and revision so the replacement matches both electrically and mechanically.
- Certifications: CE, UL, cULus — Use it as the reference when cross-checking a current-production equivalent.
- Mounting: 35-mm DIN track - mounting — Verify it in the project documentation before confirming the order.
- Rated current Ie: up to 4 A — Check this value against the nameplate of the installed unit before ordering.
- Supply voltage: 24 VDC (20.4 to 26.4 V) — Match it to the existing panel and upstream protection.
Datasheets and compliance documents are available on request; quote the full catalog number when enquiring.
Common questions about E3NX-CA0
Q.For E3NX-CA0, what does the specification table state about supply voltage?
The specification table lists supply voltage = 24 VDC (20.4 to 26.4 V) for Omron E3NX-CA0. Check the revision of the installed unit if the catalog number has been superseded.
Q.Which value is published under certifications for catalog number E3NX-CA0?
For E3NX-CA0, certifications is given as CE, UL, cULus. Compare it with the nameplate of the installed unit before ordering.
Q.Before ordering E3NX-CA0, which weight entry should be checked?
The weight entry quoted above is Approx. 185 g/approx. 95 g. Confirm this figure against the unit currently in the panel.
Q.Can the E3NX-CA0 replace the unit currently installed in my panel?
Compare catalog number E3NX-CA0 and the ratings above with the nameplate of the installed device. A current-production equivalent is selected by function and electrical rating, not by the label alone.
Q.How do I confirm compatibility of E3NX-CA0 before ordering?
Match the catalog number E3NX-CA0 and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.