IFM · Inductive proximity sensor
II5284 is an IFM circuit breaker with Breaking capacity Icu/Ics yes; Supply voltage 10...30 V DC (IEC 60947-5-2); Enclosure rating IP67 (IEC 60529). It is used in distribution boards, motor protection circuits, panel feeders where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Breaking capacity Icu/Icsyes
-
Supply voltage10...30 V DC (IEC 60947-5-2)
-
Enclosure ratingIP67 (IEC 60529)
-
Mountingnon-flush mountable
Specifications
| Electrical |
| Breaking capacity Icu/Ics |
yes |
| Supply voltage |
10...30 V DC (IEC 60947-5-2) |
| Frequency |
250 Hz |
| Overload capacity |
yes |
| I/O and communication |
| Response time |
<= 1500 Hz switching frequency |
| Mechanical |
| Dimensions (H x W x D) |
M30 x 1.5 / L = 81 mm |
| Weight |
263 g |
| Mounting |
non-flush mountable |
| Enclosure rating |
IP67 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
-25...+70 °C (IEC 60068-2-1) |
| Certifications |
CE, cULus |
Values follow the IFM Inductive proximity sensor specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| IFM Inductive proximity sensor variants |
| Catalog number |
Breaking capacity Icu/Ics |
|
II5284 (this page) |
yes |
| II5285 |
yes |
| II5256 |
yes |
| II5260 |
yes |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The II5284 is the device-level element in an IFM circuit breaker installation. It receives the field signals and control supply listed above — 10...30 V DC (IEC 60947-5-2) — and switches or conditions the load within the the rated ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in distribution boards, motor protection circuits, panel feeders, where the unit is matched to the original catalog number and the enclosure provides non-flush mountable support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for IFM II5284
IFM II5284 — Sensor or detector for object detection, distance measurement and status feedback on production lines. The figures below are taken from the specification table on this page for catalog number II5284; record the nameplate data of the unit being replaced before selecting an equivalent.
- Overload capacity: yes — Check this value against the nameplate of the installed unit before ordering.
- Response time: <= 1500 Hz switching frequency — Match it to the existing panel and upstream protection.
- Dimensions (H x W x D): M30 x 1.5 / L = 81 mm — Record it with the other nameplate data when sourcing a replacement.
- Frequency: 250 Hz — Confirm the revision of the installed unit before a like-for-like replacement.
Available from stock with datasheet, certificates and a quotation on request.
Common questions about II5284
Q.Before ordering II5284, which dimensions (H x W x D) entry should be checked?
The dimensions (H x W x D) entry quoted above is M30 x 1.5 / L = 81 mm. Compare it with the nameplate of the installed unit before ordering.
Q.Where can I find the weight data for II5284?
It is listed in the specification table for IFM II5284 as 263 g. Confirm this figure against the unit currently in the panel.
Q.For II5284, what does the specification table state about frequency?
The specification table lists frequency = 250 Hz for IFM II5284. Use the value as the reference when sourcing a current-production equivalent.
Q.What should I include in an enquiry for II5284?
Send the full catalog number II5284, the required quantity and a photo of the nameplate. Stock, lead time and the applicable compliance documents can then be confirmed for IFM II5284.
Q.Can the II5284 replace the unit currently installed in my panel?
Compare catalog number II5284 and the ratings above with the nameplate of the installed device. A current-production equivalent is selected by function and electrical rating, not by the label alone.