Honeywell · HMI panel
STD120-E1H-00000-1C-S2-AN-MB+XXXX is a Honeywell HMI panel with Supply voltage Pending confirmation from the official Honeywell data sheet; Enclosure rating Pending confirmation from the official Honeywell data sheet; Communication ports RS-232/422/485, Ethernet. It is used in machine operator panels, control cabinets, local HMI stations where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Supply voltagePending confirmation from the official Honeywell data sheet
-
Enclosure ratingPending confirmation from the official Honeywell data sheet
-
MountingPending confirmation from the official Honeywell data sheet
Specifications
| Electrical |
| Supply voltage |
Pending confirmation from the official Honeywell data sheet |
| Mechanical |
| Mounting |
Pending confirmation from the official Honeywell data sheet |
| Enclosure rating |
Pending confirmation from the official Honeywell data sheet |
| Touch type |
Pending confirmation from the official Honeywell data sheet |
| Environment and compliance |
| Operating temperature |
Pending confirmation from the official Honeywell data sheet |
| Certifications |
Pending confirmation from the official Honeywell data sheet |
Values follow the Honeywell HMI panel specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The STD120-E1H-00000-1C-S2-AN-MB+XXXX is the device-level element in a Honeywell HMI panel installation. It receives the field signals and control supply listed above — Pending confirmation from the official Honeywell data sheet — and switches or conditions the load within the the rated ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in machine operator panels, control cabinets, local HMI stations, where the unit is matched to the original catalog number and the enclosure provides Pending confirmation from the official Honeywell data sheet support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Honeywell STD120-E1H-00000-1C-S2-AN-MB
Honeywell STD120-E1H-00000-1C-S2-AN-MB — Operator panel for visualisation, parameter setting and alarm handling on a control cabinet door or console. The figures below are taken from the specification table on this page for catalog number STD120-E1H-00000-1C-S2-AN-MB; confirm the installed unit's part number and revision so the replacement matches both electrically and mechanically.
- Certifications: Pending confirmation from the official Honeywell data sheet — Use it as the reference when cross-checking a current-production equivalent.
- Touch type: Pending confirmation from the official Honeywell data sheet — Verify it in the project documentation before confirming the order.
- Operating temperature: Pending confirmation from the official Honeywell data sheet — Check this value against the nameplate of the installed unit before ordering.
- Supply voltage: Pending confirmation from the official Honeywell data sheet — Match it to the existing panel and upstream protection.
Cross-check the ratings above with the installed device before confirming the order.
Common questions about STD120-E1H-00000-1C-S2-AN-MB
Q.Which value is published under mounting for catalog number STD120-E1H-00000-1C-S2-AN-MB?
For STD120-E1H-00000-1C-S2-AN-MB, mounting is given as Pending confirmation from the official Honeywell data sheet. Compare it with the nameplate of the installed unit before ordering.
Q.Before ordering STD120-E1H-00000-1C-S2-AN-MB, which certifications entry should be checked?
The certifications entry quoted above is Pending confirmation from the official Honeywell data sheet. Confirm this figure against the unit currently in the panel.
Q.Where can I find the enclosure rating data for STD120-E1H-00000-1C-S2-AN-MB?
It is listed in the specification table for Honeywell STD120-E1H-00000-1C-S2-AN-MB as Pending confirmation from the official Honeywell data sheet. Use the value as the reference when sourcing a current-production equivalent.
Q.What should I include in an enquiry for STD120-E1H-00000-1C-S2-AN-MB?
Send the full catalog number STD120-E1H-00000-1C-S2-AN-MB, the required quantity and a photo of the nameplate. Stock, lead time and the applicable compliance documents can then be confirmed for Honeywell STD120-E1H-00000-1C-S2-AN-MB.
Q.How do I confirm compatibility of STD120-E1H-00000-1C-S2-AN-MB before ordering?
Match the catalog number STD120-E1H-00000-1C-S2-AN-MB and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.