Phoenix Contact · Contactron motor starter
2900421 is a Phoenix Contact circuit breaker with Tripping characteristic B / C / D (IEC 60947-2); Number of poles 1 / 2 / 3 / 4 (IEC 60947-2); Breaking capacity Icu/Ics 6 kA / 10 kA (IEC 60947-2). It is used in distribution boards, motor protection circuits, panel feeders where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Tripping characteristicB / C / D (IEC 60947-2)
-
Number of poles1 / 2 / 3 / 4 (IEC 60947-2)
-
Breaking capacity Icu/Ics6 kA / 10 kA (IEC 60947-2)
-
Enclosure ratingIP20 (IEC 60529)
Specifications
| Electrical |
| Rated insulation voltage Ui |
440 V (IEC 60947-2) |
| Rated impulse withstand Uimp |
4 kV (IEC 60947-2) |
| Breaking capacity Icu/Ics |
6 kA / 10 kA (IEC 60947-2) |
| Tripping characteristic |
B / C / D (IEC 60947-2) |
| Number of poles |
1 / 2 / 3 / 4 (IEC 60947-2) |
| Frequency |
≤ 2 Hz (Load-dependent) |
| Rated torque |
0.5 Nm ... 0.6 Nm |
| Mechanical |
| Weight |
308.03 g |
| Mounting |
35 mm DIN rail (IEC 60715) |
| Terminal wire size |
0.2 mm² ... 2.5 mm² |
| Enclosure rating |
IP20 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
-25...+60 °C (IEC 60068-2-1) |
| Certifications |
CE, UL, cULus |
Values follow the Phoenix Contact Contactron motor starter specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Contactron motor starter variants |
| Catalog number |
Tripping characteristic |
Breaking capacity Icu/Ics |
|
2900421 (this page) |
B / C / D (IEC 60947-2) |
6 kA / 10 kA (IEC 60947-2) |
| 2900420 |
B / C / D (IEC 60947-2) |
6 kA / 10 kA (IEC 60947-2) |
| 2900422 |
B / C / D (IEC 60947-2) |
6 kA / 10 kA (IEC 60947-2) |
| 2900414 |
B / C / D (IEC 60947-2) |
6 kA / 10 kA (IEC 60947-2) |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The 2900421 is the device-level element in a Phoenix Contact circuit breaker installation. It receives the field signals and control supply listed above — the rated supply — and switches or conditions the load within the the rated ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in distribution boards, motor protection circuits, panel feeders, where the unit is matched to the original catalog number and the enclosure provides 35 mm DIN rail (IEC 60715) support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 2900421
Phoenix Contact 2900421 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 2900421; record the nameplate data of the unit being replaced before selecting an equivalent.
- Operating temperature: -25...+60 °C (IEC 60068-2-1) — Check this value against the nameplate of the installed unit before ordering.
- Certifications: CE, UL, cULus — Match it to the existing panel and upstream protection.
- Breaking capacity Icu/Ics: 6 kA / 10 kA (IEC 60947-2) — Record it with the other nameplate data when sourcing a replacement.
- Frequency: ≤ 2 Hz (Load-dependent) — Confirm the revision of the installed unit before a like-for-like replacement.
Datasheets and compliance documents are available on request; quote the full catalog number when enquiring.
Common questions about 2900421
Q.Where can I find the operating temperature data for 2900421?
It is listed in the specification table for Phoenix Contact 2900421 as -25...+60 °C (IEC 60068-2-1). Check the revision of the installed unit if the catalog number has been superseded.
Q.For 2900421, what does the specification table state about rated insulation voltage Ui?
The specification table lists rated insulation voltage Ui = 440 V (IEC 60947-2) for Phoenix Contact 2900421. Compare it with the nameplate of the installed unit before ordering.
Q.Which value is published under mounting for catalog number 2900421?
For 2900421, mounting is given as 35 mm DIN rail (IEC 60715). Confirm this figure against the unit currently in the panel.
Q.How do I confirm compatibility of 2900421 before ordering?
Match the catalog number 2900421 and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.
Q.Can the 2900421 replace the unit currently installed in my panel?
Compare catalog number 2900421 and the ratings above with the nameplate of the installed device. A current-production equivalent is selected by function and electrical rating, not by the label alone.