Phoenix Contact · Temperature Transmitter
2865450 is a Phoenix Contact circuit breaker with Tripping characteristic 7 mm; Breaking capacity Icu/Ics 8 mA; Supply voltage 11...30 V DC (loop powered). It is used in distribution boards, motor protection circuits, panel feeders where the installed unit is matched to the original catalog number and a compact, documented part is required.
-
Tripping characteristic7 mm
-
Breaking capacity Icu/Ics8 mA
-
Supply voltage11...30 V DC (loop powered)
-
Enclosure ratingIP66 / IP67 (IEC 60529)
Specifications
| Electrical |
| Rated insulation voltage Ui |
375 V PP |
| Breaking capacity Icu/Ics |
8 mA |
| Tripping characteristic |
7 mm |
| Supply voltage |
11...30 V DC (loop powered) |
| Output voltage |
9.6 V |
| Output current |
10 mA |
| Frequency |
≤ 20 Hz (without load) |
| Rated torque |
0.5 Nm ... 0.6 Nm |
| Mechanical |
| Weight |
186 g |
| Mounting |
DIN rail mounting |
| Terminal wire size |
0.2 mm² ... 2.5 mm² |
| Enclosure rating |
IP66 / IP67 (IEC 60529) |
| Environment and compliance |
| Operating temperature |
-40...+85 °C (IEC 60068-2-1) |
| Certifications |
CE, UL, cULus |
| Humidity |
10 % ... 95 % (non-condensing) |
Values follow the Phoenix Contact Temperature Transmitter specification for this catalog number; parameters not confirmed for this variant are omitted rather than estimated.
Model comparison in the same family
| Phoenix Contact Temperature Transmitter variants |
| Catalog number |
Tripping characteristic |
Breaking capacity Icu/Ics |
|
2865450 (this page) |
7 mm |
8 mA |
| 2865405 |
7 mm |
— |
| 2865434 |
7 mm |
8 mA |
| 2865476 |
7 mm |
8 mA |
Before selecting an alternative, confirm its dimensions, terminals and installation requirements in the manufacturer documentation.
Where it sits in the control system
The 2865450 is the device-level element in a Phoenix Contact circuit breaker installation. It receives the field signals and control supply listed above — 11...30 V DC (loop powered) — and switches or conditions the load within the the rated ratings shown in the Specifications table. Wiring and protective devices are sized to those same numbers, not to a generic assumption.
Typical installations place it in distribution boards, motor protection circuits, panel feeders, where the unit is matched to the original catalog number and the enclosure provides DIN rail mounting support. Record the catalog number and revision from the nameplate of the installed unit before specifying a like-for-like spare.
Selection notes for Phoenix Contact 2865450
Phoenix Contact 2865450 — Industrial automation component supplied as a like-for-like replacement, selected by catalog number and published ratings. The figures below are taken from the specification table on this page for catalog number 2865450; record the nameplate data of the unit being replaced before selecting an equivalent.
- Output voltage: 9.6 V — Use it as the reference when cross-checking a current-production equivalent.
- Frequency: ≤ 20 Hz (without load) — Verify it in the project documentation before confirming the order.
- Terminal wire size: 0.2 mm² ... 2.5 mm² — Check this value against the nameplate of the installed unit before ordering.
- Output current: 10 mA — Match it to the existing panel and upstream protection.
Available from stock with datasheet, certificates and a quotation on request.
Common questions about 2865450
Q.Which value is published under rated torque for catalog number 2865450?
For 2865450, rated torque is given as 0.5 Nm ... 0.6 Nm. Check the revision of the installed unit if the catalog number has been superseded.
Q.Before ordering 2865450, which certifications entry should be checked?
The certifications entry quoted above is CE, UL, cULus. Compare it with the nameplate of the installed unit before ordering.
Q.Where can I find the enclosure rating data for 2865450?
It is listed in the specification table for Phoenix Contact 2865450 as IP66 / IP67 (IEC 60529). Confirm this figure against the unit currently in the panel.
Q.How do I confirm compatibility of 2865450 before ordering?
Match the catalog number 2865450 and the specification values listed above against the installed unit, then confirm the firmware or hardware revision where a revision-sensitive part is involved.
Q.Can the 2865450 replace the unit currently installed in my panel?
Compare catalog number 2865450 and the ratings above with the nameplate of the installed device. A current-production equivalent is selected by function and electrical rating, not by the label alone.